RF PCB Stackup Planning

Metal Core RF Stackup | Aluminum Backed Antenna Board

A metal core RF stackup bonds high-frequency laminate directly to an aluminum or copper base plate, delivering superior thermal management and a rigid ground reference for antenna and power amplifier boards. This guide covers layer construction, core thickness selection, material…

Cross-section of an aluminum metal core PCB with dielectric and copper layers

What Is a Metal Core RF Stackup?

A metal core RF stackup replaces the conventional FR-4 or all-laminate substrate with a thick aluminum (or sometimes copper) base plate bonded to one or more RF dielectric layers through a thermally conductive insulating film. The metal base serves simultaneously as a heatsink, a mechanical stiffener, and the lowest ground reference plane. Thermal conductivity of the metal core—typically 150–230 W/m·K for aluminum alloys 5052 or 6061—is roughly 500× higher than standard FR-4 (≈ 0.3 W/m·K), which is why metal core boards dominate high-power LED lighting and increasingly appear in RF power amplifiers, active antenna arrays, and radar T/R modules where junction temperatures must stay below safe limits.

Why Use a Metal Core for RF and Antenna Boards?

Patch antenna array on an aluminum-backed RF board

Thermal Performance

High-power GaN or LDMOS amplifier dies can dissipate 10–50 W per device. A standard multilayer RF board relies on thermal vias to conduct heat to an external heatsink, but each via adds inductance and occupies routing area. An aluminum-backed stackup conducts heat laterally and vertically through the base plate itself, cutting board-level thermal resistance by 5–10× compared with a vias-only approach. This keeps device junction temperatures lower, improving both reliability and RF gain flatness over temperature.

Ground Plane Integrity

The continuous metal base acts as an unbroken ground reference with negligible sheet resistance. For patch antennas, this means a predictable image plane that improves gain and front-to-back ratio. For power amplifiers, it lowers ground inductance and reduces common-mode noise.

Mechanical Rigidity

A 1.0–3.0 mm (40–120 mil) aluminum plate keeps the board flat under thermal cycling, which matters for connectorized assemblies and waveguide interfaces that demand tight coplanarity tolerances—often ±50 µm or better.

Typical Metal Core RF Stackup Construction

The simplest build is a single-sided RF metal core board: one copper signal layer on top of a dielectric bonded to the aluminum base. More capable designs add a second copper layer between the dielectric and the base, or bond a full two-layer RF laminate onto the metal core. Below is a representative four-layer build used for an active antenna element with an integrated PA:

Layer Material Typical Thickness Function
L1 – Top copper ED copper, ½ oz or 1 oz 18–35 µm Patch antenna / signal traces
Dielectric 1 Rogers RO4350B (Dk 3.48, Df 0.0037) 0.254–0.508 mm (10–20 mil) RF transmission medium
L2 – Inner copper 1 oz copper 35 µm Ground / stripline reference
Bonding dielectric Thermally conductive prepreg or adhesive film 75–150 µm (3–6 mil) Electrical isolation + thermal path
Metal core Aluminum 5052-H32 1.0–2.0 mm (40–80 mil) Heatsink / mechanical base / ground

When the design mixes standard digital layers with an RF front end on a metal core, engineers sometimes adopt a hybrid laminate stackup where different Dk materials share the same board, bonded above the metal base.

Choosing the Right Core Thickness

Core thickness in a metal core RF stackup refers to both the metal base plate and the RF dielectric layer above it. The dielectric thickness sets impedance and coupling; the metal thickness sets thermal and mechanical performance. A thicker aluminum plate spreads heat further laterally but adds weight and cost, while a thinner dielectric tightens trace widths for 50 Ω impedance and increases capacitive coupling to ground—useful for compact patch antennas but harmful for wide-band microstrip feeds.

Use the calculator below to find a suitable core thickness for your dielectric layer based on impedance targets and material Dk. Enter the target impedance, dielectric constant, and copper weight to see the recommended core height.

Loading Core Thickness Finder…

For example, targeting 50 Ω on RO4350B (Dk 3.48) with 1 oz copper returns a dielectric thickness near 0.30 mm (12 mil). If your thermal budget demands a thicker aluminum plate underneath, that choice is independent of the dielectric height—but verify that the total board thickness still fits your enclosure and connector keep-out. You can cross-check trace widths against our impedance table by material to confirm the geometry before committing to fabrication.

Finished Board Thickness and Stackup Accumulation

Because the metal base plate dominates the total thickness, a metal core RF board is often 2–4 mm thick—much more than a typical four-layer RF laminate at 0.8–1.6 mm. Connectors, housing pockets, and thermal interface material gaps all depend on knowing the exact finished thickness. Add up every layer—copper foils, dielectric sheets, bonding adhesive, and the aluminum plate—to get an accurate number.

Loading Board Thickness Accumulator…

A realistic result for the four-layer stackup in the table above: 18 µm top copper + 0.508 mm RO4350B + 35 µm inner copper + 0.100 mm bond film + 1.5 mm aluminum = 2.161 mm total. Confirm this against your mechanical enclosure drawing and ensure the thermal pad footprint on the housing matches the metal core outline. If the finished thickness is too tall for your system, reducing the aluminum plate to 1.0 mm saves 0.5 mm while still providing far better thermal performance than an all-laminate board.

Dielectric and Bonding Material Selection

Thermal vias connecting copper pads to a metal core base plate

The RF dielectric layer must satisfy both electrical and thermal requirements. Common choices include:

  • Rogers RO4350B / RO4003C — thermoset hydrocarbon laminates, Dk 3.48 / 3.55, Df < 0.004 at 10 GHz, compatible with standard FR-4 processing. Good to roughly 20 GHz for most antenna work.
  • Rogers RT/duroid 5880 — PTFE/glass, Dk 2.20, Df 0.0009, excellent for low-loss feeds above 10 GHz but requires sodium-etch surface preparation before bonding.
  • Isola Astra MT77 — very low loss (Df 0.0017 at 10 GHz), suitable for 5G mmWave antenna arrays where every 0.1 dB matters.

The bonding dielectric between the RF laminate and the metal plate is the thermal bottleneck. Standard epoxy bond films have thermal conductivity around 0.5–1.0 W/m·K. Specialty thermally conductive adhesives (e.g., Bergquist or Henkel products) reach 1.5–3.0 W/m·K, cutting the thermal resistance of that interface layer by 3–6×. Always request the bond-film thermal conductivity on the fabrication drawing—if left unspecified, the shop will default to the cheapest option, which may not meet your thermal budget. For a broader look at how dielectric constant and loss tangent drive laminate choice, see the RF PCB material selection guide.

Design Rules and Fabrication Constraints

Drilling and Routing

Through-holes in a metal core board pass through aluminum, which dulls carbide drill bits quickly. Most fabricators limit hole diameters to ≥ 0.3 mm (12 mil) and charge a premium for hole counts above a few hundred. Mechanical routing of the board outline is done with diamond-coated or carbide end mills; tight internal cutouts are expensive. Avoid blind or buried vias in the metal core layer—they are impractical. If you need via transitions between RF layers above the metal base, consider a back-drilled stackup approach for stub control on higher-frequency signals.

Thermal Via Arrays

Even with a metal core, thermal vias under high-power devices are still useful. They short-circuit the dielectric layer’s thermal resistance and connect the device ground pad directly to the aluminum plate. Use 0.3 mm vias on a 0.6 mm pitch, filled and capped, directly under the die attach pad.

Surface Finish

ENIG (electroless nickel / immersion gold) is the default for RF metal core boards because it provides a flat, solderable, and corrosion-resistant surface. For wire-bond PA die, use electrolytic soft gold at ≥ 0.75 µm thickness over a nickel barrier. Avoid OSP on metal core boards—the exposed aluminum edges corrode in the OSP chemistry.

When Metal Core Is Not the Right Choice

Metal core RF stackups add cost and complexity. They are overkill when the board dissipates under 1–2 W total, when the design needs more than two RF signal layers, or when the operating frequency exceeds roughly 40 GHz (where surface roughness and dielectric thickness tolerances on the bond film become critical). For low-power antenna boards like sub-GHz ISM-band designs, a standard two-layer or four-layer laminate on FR-4 or a low-cost hydrocarbon is lighter, cheaper, and perfectly adequate thermally.

Also consider that aluminum has a CTE of about 23 ppm/°C—much higher than copper’s 17 ppm/°C and far higher than ceramic-filled laminates (10–12 ppm/°C). Under aggressive thermal cycling (–40 °C to +125 °C), CTE mismatch between the metal core and the RF laminate can stress solder joints and delaminate the bond film. IPC-6012 Class 3 reliability testing should be specified for any metal core RF board destined for automotive radar or aerospace applications.

Stackup Documentation Checklist

Before releasing your metal core RF stackup to fabrication, confirm every item below is on the drawing or in the fabrication notes:

  1. Metal base alloy and temper (e.g., Al 5052-H32)
  2. Metal base thickness with tolerance (e.g., 1.50 ± 0.10 mm)
  3. RF dielectric material, grade, and Dk/Df values at the operating frequency
  4. Dielectric thickness with tolerance
  5. Bond film material and thermal conductivity (W/m·K)
  6. Copper weights on each layer
  7. Impedance targets with tolerance (e.g., 50 Ω ± 5 %)
  8. Surface finish and gold thickness if wire bonding
  9. Thermal via pattern and fill requirement
  10. Total finished board thickness with tolerance

For downloadable reference stackups you can adapt to your own project, browse the stackup library index.

Frequently Asked Questions

Can I use copper instead of aluminum for the metal core?

Yes. Copper cores offer about 2.5× higher thermal conductivity (390 W/m·K vs 150–230 W/m·K for aluminum) but weigh roughly 3× more and cost significantly more. Copper cores are common in GaN power amplifier pallets where thermal performance is the top priority and weight is secondary.

What frequency range suits a metal core RF stackup?

Metal core builds work well from DC through roughly 30 GHz. Above that, dielectric thickness tolerances on the thin bond film and surface roughness on the aluminum become limiting factors. For 77 GHz automotive radar, for instance, the industry favors all-laminate stackups on materials like Rogers RO3003 without a metal core.

How does a metal core stackup affect antenna performance?

The continuous metal base improves patch antenna gain by 0.5–1.5 dB compared with a meshed or via-stitched ground plane, because it eliminates ground-plane inductance and leakage. However, the rigid metal plate prevents any flexing, so conformal antenna applications are ruled out.

Is a metal core board compatible with standard SMT assembly?

Yes, with caveats. The high thermal mass of the aluminum base requires a slower reflow profile—extend the soak zone by 30–60 seconds and confirm peak temperature reaches the solder paste specification across the entire board. Vapor-phase reflow is preferred for uniform heating.

Ready for a quotation?

Send your requirements for a material, stackup and manufacturing review. Price and schedule are confirmed for your project.

Upload Gerber