
Why Megtron 7 for 112G Backplane Channels
An 8-layer Megtron 7 stackup is the baseline construction for 112 Gbps (PAM4) backplane and orthogonal-direct-attach links where channel loss must stay below roughly 30 dB at the Nyquist frequency of 26.5625 GHz. Panasonic Megtron 7 (R-5785N) delivers a Dk of 3.37 and a Df of 0.002 at 10 GHz—among the lowest of any glass-reinforced hydrocarbon laminate—making it the material of choice when PTFE is too expensive or too difficult to process in high-layer-count builds.
Compared to Megtron 6 (Df ≈ 0.004), the halved loss tangent of Megtron 7 saves approximately 0.8–1.0 dB/inch at 28 GHz on a typical stripline, which translates directly into longer reach or wider eye margin for 112G-per-lane OIF CEI-112G-LR links. When selecting among high-frequency PCB materials, Megtron 7 occupies the sweet spot between modified-epoxy laminates and full PTFE systems.
Material Parameters at a Glance

| Parameter | Megtron 7 (R-5785N) | Megtron 6 (R-5775K) | Standard High-Tg FR-4 |
|---|---|---|---|
| Dk @ 10 GHz | 3.37 | 3.71 | 4.2–4.5 |
| Df @ 10 GHz | 0.002 | 0.004 | 0.018–0.025 |
| Tg (°C, DSC) | 210 | 185 | 170 |
| Td (°C, 5 % wt loss) | 410 | 400 | 310–340 |
| CTE z-axis (ppm/°C, below Tg) | 28 | 30 | 45–65 |
| CAF resistance | Excellent | Good | Moderate |
The low z-axis CTE and high Td of Megtron 7 matter for reliability in 8+ layer builds with multiple reflow cycles. Its Panasonic R-5785N datasheet confirms UL 94 V-0 flammability and IPC-4101/40 qualification.
8-Layer Stackup: Layer-by-Layer Build
The stackup below is a symmetrical construction optimized for broadside-coupled differential striplines on layers 3 and 6, with microstrip pairs on layers 1 and 8 for breakout routing. All dielectric thicknesses assume Megtron 7 core and prepreg; adjust prepreg flow for your specific glass style (1078, 2116, or 1035 spread glass preferred for skew control).
| Layer | Function | Cu Weight | Dielectric Above (mil) | Material |
|---|---|---|---|---|
| L1 | Signal (diff pair, microstrip) | 1 oz (H-VLP) | — | — |
| 4.0 | M7 prepreg 1035 × 2 | |||
| L2 | Ground plane | 1 oz | ||
| 5.0 | M7 core | |||
| L3 | Signal (diff pair, stripline) | 0.5 oz (H-VLP) | ||
| 12.0 | M7 prepreg 2116 × 2 | |||
| L4 | Ground / power plane | 1 oz | ||
| 12.0 | M7 core (symmetry axis) | |||
| L5 | Power / ground plane | 1 oz | ||
| 12.0 | M7 prepreg 2116 × 2 | |||
| L6 | Signal (diff pair, stripline) | 0.5 oz (H-VLP) | ||
| 5.0 | M7 core | |||
| L7 | Ground plane | 1 oz | ||
| 4.0 | M7 prepreg 1035 × 2 | |||
| L8 | Signal (diff pair, microstrip) | 1 oz (H-VLP) | — | — |
Total board thickness lands near 75–80 mil (1.9–2.0 mm), which suits standard backplane connector footprints. Hyper-very-low-profile (H-VLP) copper foil with Rz ≤ 2 µm is mandatory on signal layers; rougher foil can add 0.3 dB/inch at 28 GHz and wipe out the Df advantage of Megtron 7.
Trace Geometry Targets
- Stripline differential pairs (L3, L6): 4.0 mil trace / 6.0 mil space, 100 Ω differential impedance, referenced to adjacent ground planes.
- Microstrip differential pairs (L1, L8): 4.5 mil trace / 7.0 mil space, 100 Ω differential impedance with solder-mask coating (Dk ≈ 3.3 for conformal mask).
- Single-ended control lines: 50 Ω, routed on signal layers only where needed for JTAG, I²C, or sideband.
If your design also includes a mixed-Dk stackup with FR-4 in the power core to reduce cost, keep the signal-layer dielectrics pure Megtron 7 and confine the FR-4 to the L4–L5 core, which carries no high-speed traces.
Via Strategy: Back-Drill and Annular Ring
At 112 Gbps PAM4, via stubs longer than 8 mil degrade the channel. Back-drilling is non-negotiable for through-hole vias connecting to L3 or L6. Target a remaining stub length of 6 mil or less; specify a back-drill depth tolerance of ±4 mil and verify with cross-section coupon. For a deeper look at drill tolerances and stub measurement, see the back-drill stackup design guide.
Annular Ring Requirements
IPC-6012 Class 3 requires a minimum annular ring of 2 mil (50 µm) on internal layers after all registration shifts. For Megtron 7 builds, the harder laminate drills cleanly, but the low-resin prepreg can shift during lamination, so many fabricators call out a 3 mil minimum annular ring on inner layers as a process guard band. Use the checker below to verify your pad and drill combination meets the target before releasing Gerbers.
For example, a 12 mil finished hole with a 22 mil pad on L3 yields a nominal annular ring of 5 mil—comfortable for Class 3. If your fabricator’s drill-to-copper registration is ±2.5 mil, the worst-case annular ring drops to 2.5 mil, still above the 2 mil floor. Tighten the pad to 20 mil and the worst case falls to 1.5 mil—below spec—so keep pads at 22 mil minimum for this drill size.
Antipad and Return-Via Placement
- Antipad diameter: 30–32 mil for a 12 mil drill; keep capacitive loading below 0.15 pF per via.
- Return vias: Place ground vias within 20 mil of every signal via to maintain the return-current path and control via impedance to ≈ 45–50 Ω differential.
- Via pitch: 39.37 mil (1.0 mm) BGA-compatible pitch is standard for most 112G retimer and connector footprints.
Glass-Weave Skew Mitigation
Intra-pair skew from glass-weave periodicity is a leading cause of PAM4 eye closure. Megtron 7 is available in spread-glass (flat-fiber) styles such as 1035 and 1078, which reduce the peak-to-valley Dk variation across the weave from roughly ±0.15 (standard 2116) to ±0.03. Specify spread glass on every dielectric layer adjacent to a signal layer. Rotate differential pairs 5–11° off the warp direction in layout to further average out any residual periodicity.
Fabrication and Process Notes

- Lamination: Megtron 7 prepreg cures at 190–200 °C with a ramp rate of 2–3 °C/min. Exceeding 210 °C risks partial Tg shift; follow Panasonic’s recommended press cycle.
- Drilling: Megtron 7 is harder than standard FR-4. Use fresh carbide bits, hit counts ≤ 500 per bit for holes ≤ 12 mil, and verify hole-wall quality with micro-section at first article.
- Surface finish: ENIG or ENEPIG for BGA pads; immersion silver for press-fit connector areas. Avoid HASL—thermal shock on a Megtron 7 panel can stress plated through-holes.
- Impedance testing: TDR coupons with the same trace geometry and dielectric as the production panel; tolerance ±7 % for 100 Ω differential stripline.
For designs that need embedded MMIC recesses alongside the backplane channel, a cavity RF stackup can be combined with the Megtron 7 signal layers, though this adds lamination complexity.
Landed Cost Considerations
Megtron 7 laminate costs roughly 3–5× more than standard high-Tg FR-4 per panel, but the total landed cost of a backplane includes far more than raw material. Tooling charges, back-drill processing, H-VLP foil upcharges, impedance coupon testing, and logistics all contribute. Use the calculator below to estimate the total landed cost of your 8-layer Megtron 7 panels including import duties and shipping, so you can compare against a Megtron 6 or HDI mmWave build on a like-for-like basis.
A typical 18 × 24 inch backplane panel in 8-layer Megtron 7 with back-drill and ENIG finish might land at 2.5–4× the cost of an equivalent Megtron 6 build. The premium is justified when channel simulations show Megtron 6 cannot close the eye at the target BER of 1 × 10⁻⁶ pre-FEC. If margin exists with Megtron 6, use it—over-specifying material is the fastest way to blow a BOM budget.
Design Checklist
- Confirm Df ≤ 0.002 @ 10 GHz on the laminate certificate of conformance.
- Specify H-VLP (Rz ≤ 2 µm) copper on all signal layers.
- Use spread-glass prepreg (1035 or 1078) adjacent to every signal layer.
- Back-drill all through-hole vias on signal nets; stub ≤ 6 mil.
- Annular ring ≥ 3 mil on inner layers after worst-case registration.
- Place return-path ground vias within 20 mil of every signal via.
- TDR impedance coupons on every production panel; ±7 % tolerance.
- Cross-section first-article for back-drill depth, hole-wall quality, and dielectric thickness.
Frequently Asked Questions
Is Megtron 7 the same as Megtron 7N?
No. Megtron 7 (R-5785N) is the ultra-low-loss grade with Df 0.002. Megtron 7N (R-5785GN) is a newer variant with improved CAF resistance and slightly different resin chemistry, but the same Dk/Df class. Always confirm the Panasonic resin code on your purchase order.
Can I mix Megtron 7 signal layers with FR-4 power cores?
Yes, and it is common practice to reduce cost. Keep all dielectrics touching signal traces as Megtron 7 and confine FR-4 to the L4–L5 power/ground core. CTE mismatch is manageable in an 8-layer build if the FR-4 Tg is ≥ 170 °C. See the hybrid stackup design method for placement rules.
What is the maximum frequency Megtron 7 supports?
Megtron 7 is characterized and used up to approximately 50 GHz in production backplanes and test fixtures. Above 40 GHz, conductor loss (copper roughness) dominates over dielectric loss, so the laminate Df advantage narrows. For 77 GHz radar or higher, PTFE or LCP substrates are typically required.
Does Megtron 7 require special handling in the fab shop?
It requires tighter drill-bit management (lower hit counts), a controlled lamination profile, and careful desmear chemistry tuned for hydrocarbon resin rather than standard epoxy. Not every fabricator is qualified—request Megtron 7 process qualification data and IPC-6012 Class 3 certification before committing.
Ready for a quotation?
Send your requirements for a material, stackup and manufacturing review. Price and schedule are confirmed for your project.
