PCB Antenna and Feed Resources

Vivaldi Antenna Design | Ultra-Wideband Tapered Slot

A complete guide to Vivaldi antenna design on PCB, covering exponential taper geometry, substrate and slot fabrication rules, feed transitions, and a practical design checklist for ultra-wideband tapered-slot antennas from 1 GHz to beyond 40 GHz.

Vivaldi tapered-slot antenna etched on a high-frequency PCB laminate

What Is a Vivaldi Antenna?

A Vivaldi antenna is an end-fire, travelling-wave antenna formed by a gradually widening (tapered) slot etched into one or both copper layers of a PCB. Its operating bandwidth routinely exceeds 10:1—covering, for example, 2–20 GHz on a single element—making it one of the widest-bandwidth planar antennas available. The taper converts a tightly bound slot-line mode at the narrow end into a radiating wave at the open mouth, producing a directive, linearly polarized beam along the board edge. Because the entire structure is a single copper pattern with no vias or stubs required for the radiator itself, the Vivaldi is straightforward to fabricate and scales from UHF through millimeter-wave frequencies.

Why Choose a Vivaldi Over Other Wideband Antennas?

Microstrip-to-slotline feed transition cross-section for a Vivaldi antenna

Engineers reach for a Vivaldi when they need end-fire radiation, wide instantaneous bandwidth, and moderate gain (typically 5–12 dBi for a single element) in a flat, PCB-compatible form factor. Compared with a spiral antenna, which radiates broadside with circular polarization, the Vivaldi fires along the substrate plane—ideal for phased arrays that tile edge-to-edge. Relative to a horn, it is lighter, cheaper, and integrates directly into a printed-circuit stackup.

Common application domains include ground-penetrating radar (GPR), electronic warfare, UWB impulse systems in the 3.1–10.6 GHz band, radio astronomy feed arrays, and MIMO radar virtual-array layouts where many identical elements must pack tightly.

Core Geometry of the Tapered Slot

Exponential Taper Profile

The classic Vivaldi uses an exponential curve to define the slot edges. In a Cartesian system with the propagation axis along x, each edge follows:

y(x) = ± C · eRx

where C sets the initial slot half-width at the feed point and R is the taper rate. A higher R opens the slot more aggressively, producing a shorter antenna but with less directivity and a higher low-frequency cutoff. A lower R yields a longer, more directive element with better low-frequency performance.

Key Dimensional Rules of Thumb

Parameter Typical Guideline Effect of Deviation
Total antenna length L ≥ λlow / 2 (one half-wavelength at lowest frequency) Shorter → higher low-frequency cutoff, reduced gain
Mouth opening width W ≈ λlow / 2 Narrower → lower directivity, wider E-plane beamwidth
Slot-line gap at feed g 0.1–0.3 mm (4–12 mil) for microwave; scales with frequency Too wide → poor slot-line mode confinement; too narrow → fabrication risk
Substrate thickness h 0.5–1.6 mm for 1–18 GHz; thinner for mmWave Thicker → stronger substrate modes, pattern distortion above ~15 GHz
Taper rate R 0.02–0.15 mm−1 (application dependent) Higher → compact but lower gain; lower → longer but sharper beam

Corrugations and Cavity Termination

Adding periodic corrugations (small transverse slots) along the outer edges of the taper improves the E-plane beamwidth symmetry and suppresses side lobes by up to 3–5 dB. At the narrow (throat) end, a circular or elliptical cavity termination reflects the residual slot-line energy back into the taper, smoothing the low-frequency impedance match. The cavity diameter is typically λmid/4 to λmid/2.

Substrate Selection for Vivaldi Antennas

Because the Vivaldi radiates from the slot, not from a patch resonator, the substrate’s role is primarily mechanical support and feed-line routing. Still, dielectric constant and loss tangent matter:

  • Low-Dk laminates (Dk 2.2–3.0) such as Rogers RT/duroid 5880 (Dk 2.20, Df 0.0009) or Taconic TLY-5 are preferred when maximum bandwidth and minimal beam squint are needed. The lower Dk reduces surface-wave excitation and keeps the effective slot-line impedance high.
  • Mid-Dk laminates (Dk 3.3–3.7) like Rogers RO4350B (Dk 3.48, Df 0.0037) offer a good cost-performance balance for designs below 18 GHz where a few percent bandwidth loss is acceptable.
  • Standard FR-4 (Dk ≈ 4.3–4.8) can work for single-octave Vivaldis below 6 GHz, but its high Df (0.02 typical) and Dk variation with frequency make it unsuitable for decade-bandwidth or millimeter-wave designs.

For a deeper comparison of UWB antenna substrate trade-offs, consider both the laminate cost and the achievable impedance bandwidth before committing to a material.

Feed Transition Design

Microstrip-to-Slotline Transition

The most common feed is a microstrip line on one side of the board crossing the slot on the opposite side at a right angle. The microstrip stub extends a quarter-wavelength (at mid-band) past the slot to present a virtual short circuit, while a circular or radial slot-line cavity on the opposite end presents a virtual open. This balun-like transition achieves 10 dB return loss across a 6:1 bandwidth when the stub and cavity dimensions are optimized together.

Stripline and Antipodal Feeds

The antipodal Vivaldi places one flare on the top copper layer and the mirrored flare on the bottom layer, overlapping at the feed. This eliminates the need for a separate balun and extends the bandwidth further—often beyond 10:1—but produces cross-polarization 5–10 dB higher than the classic single-sided design. A balanced antipodal variant adds a third copper layer to suppress this cross-pol, at the cost of a more complex stackup.

Slot Milling and Fabrication Rules

The narrow throat of a Vivaldi antenna is the most fabrication-critical feature. Whether the slot is chemically etched or mechanically milled, the minimum achievable slot width, copper-to-edge clearance, and internal corner radii all affect the antenna’s impedance match at the upper end of its band. A slot that is wider than designed shifts the slot-line characteristic impedance upward and degrades the feed transition.

Before finalizing your Gerber files, run the slot geometry through a milling-rule checker to confirm your fabricator can hold the required tolerances. Enter your minimum slot width, board thickness, and copper weight below:

Loading Slot Milling Rule Checker…

For a typical 0.2 mm (8 mil) throat slot in 0.508 mm (20 mil) RO4350B with 1 oz copper, the checker will flag whether a standard 0.2 mm end mill can clear the slot without undercutting adjacent copper. If the tool flags a violation, widen the throat by 0.05 mm increments and re-simulate—each increment shifts the low-end impedance by roughly 2–5 Ω, so verify the match in your EM solver. Consult IPC-2221B generic design requirements for minimum annular ring and conductor spacing rules that interact with slot geometry.

Simulation and Measurement Workflow

Dual-polarized Vivaldi antenna array in egg-crate assembly

Full-Wave Simulation

Vivaldi antennas are best simulated with time-domain solvers (CST Microwave Studio’s transient solver, or Ansys HFSS with broadband adaptive meshing) because a single run covers the entire operating band. Key outputs to monitor are S11 below −10 dB across the target band, realized gain versus frequency, and E/H-plane radiation patterns at several spot frequencies. Consult an antenna simulation workflow for solver setup details including boundary padding (≥ λlow/4 air box on every side) and mesh density at the throat.

Prototype Measurement

Because the Vivaldi is end-fire, standard far-field chamber setups must orient the antenna so the board edge faces the receive horn. Near-field planar scanning is also effective—place the scan plane perpendicular to the board and parallel to the mouth opening. Gain calibration with a standard-gain horn at mid-band, plus a swept return-loss measurement on a calibrated VNA, covers the essential verification. For guidance on chamber and OTA setups, see the antenna measurement setup guide.

Common Design Mistakes

  • Ignoring substrate-mode coupling: A substrate thicker than ~0.03 λ at the highest operating frequency will excite surface waves that distort the pattern and raise cross-polarization. Thin the board or add mode-suppression vias along the taper edges.
  • Under-sizing the backside ground: In a classic (non-antipodal) Vivaldi, the ground plane on the microstrip side must extend well beyond the slot mouth. Truncating it introduces edge diffraction ripple in the H-plane pattern.
  • Neglecting the connector launch: An SMA or SMPM connector soldered at the board edge adds a reactive discontinuity. De-embed it in simulation or use a tapered microstrip-to-connector transition.
  • Forgetting corrugation impact on slot width: Corrugation teeth narrow the effective mouth, reducing gain. Re-optimize the taper rate after adding corrugations.

A broader catalogue of pitfalls is covered in common antenna design mistakes.

Vivaldi Arrays and System Integration

Vivaldi elements tile naturally into linear or planar arrays because the thin board profile allows element spacing below λ/2 at the highest frequency. In a dual-polarized configuration, orthogonal Vivaldis interleave in an “egg-crate” assembly. Array-level considerations include:

  • Mutual coupling: Adjacent elements share the same dielectric slab, coupling through surface waves. Full-array simulation (or at least a 3×3 active-element pattern) is necessary to capture scan-blindness angles.
  • Feed network: Wideband corporate feed networks using Wilkinson dividers on low-loss laminate, or direct coaxial feeds per element, are typical. Beamforming across a 10:1 bandwidth requires true-time-delay (TTD) rather than phase shifters to avoid beam squint.
  • Radome interaction: A flat dielectric radome in front of the array mouth shifts the aperture impedance. Budget 0.5–1.0 dB of additional mismatch loss and verify with a radome dielectric and thickness analysis.

Vivaldi Antenna Design Checklist

Before releasing your design to fabrication, walk through every critical parameter. The interactive checklist below lets you tick off substrate, geometry, feed, simulation, and fabrication items and generates a summary you can attach to your design review package:

Loading Design Checklist Builder…

A completed checklist should confirm at minimum: substrate Dk and thickness verified against datasheet values at the operating frequency, taper profile exported from the parametric equation (not hand-drawn), slot throat width within fabricator capability, feed-transition stub length set to λ/4 at geometric-mean frequency, S11 below −10 dB across the full band in simulation, and connector footprint matched to the microstrip impedance. Any open item is worth one more simulation iteration before committing to copper.

Frequently Asked Questions

What bandwidth can a single Vivaldi antenna achieve?

A well-designed single Vivaldi element routinely achieves 10:1 instantaneous bandwidth (e.g., 2–20 GHz). Antipodal variants have demonstrated up to 18:1 in published research, though cross-polarization increases at the extremes. The practical limit is set by the antenna length at the low end and substrate-mode onset at the high end.

Can I build a Vivaldi antenna on FR-4?

Yes, for limited bandwidths (roughly 3:1) below 6 GHz. FR-4’s Dk varies significantly with frequency (4.3 at 1 GHz to ~4.7 at 10 GHz) and its loss tangent of ~0.02 degrades gain at higher frequencies. For decade-bandwidth or millimeter-wave Vivaldis, use a PTFE or hydrocarbon-ceramic laminate.

How does the Vivaldi compare to a tapered-slot antenna (TSA)?

“Vivaldi antenna” and “tapered slot antenna” are often used interchangeably when the taper is exponential. Strictly, TSA is the broader category—it includes linear and constant-width tapers as well. The Vivaldi specifically uses an exponential (or sometimes elliptical) taper, which gives the best impedance-bandwidth product among the TSA family.

What gain can I expect from a single Vivaldi element?

Gain increases with frequency because the electrical length of the taper grows. Typical values range from 4–5 dBi near the low-frequency cutoff to 10–12 dBi at the upper end. Adding corrugations or dielectric-lens loading at the mouth can push peak gain above 14 dBi.

Is the Vivaldi suitable for phased-array radar?

Absolutely. The Vivaldi is one of the most popular elements for wideband phased arrays, especially in electronic-warfare and IEEE-documented radar systems. Its planar form factor, end-fire pattern, and inherent wideband match make it ideal for dense, dual-polarized apertures scanned to ±45° or more.

Ready for a quotation?

Send your requirements for a material, stackup and manufacturing review. Price and schedule are confirmed for your project.

Upload Gerber