
What Is MIMO Radar Design?
MIMO (Multiple-Input Multiple-Output) radar design uses multiple transmit (TX) and receive (RX) antennas that radiate orthogonal waveforms simultaneously, then separates those waveforms in the receiver to synthesize a virtual array much larger than the physical aperture. A system with NTX transmitters and NRX receivers creates up to NTX × NRX virtual elements, dramatically improving angular resolution without a proportional increase in hardware channels. This principle is the foundation of modern 77 GHz automotive radar, where a 3 TX / 4 RX transceiver like the Texas Instruments AWR2243 yields a 12-element virtual array on a board smaller than a credit card.
Virtual Array Formation

How the Virtual Array Works
Each TX–RX pair measures the round-trip phase of a target. Because the total path length equals the TX-to-target plus target-to-RX distance, the phase center of each pair sits at the midpoint of the TX element and the RX element. Collecting all NTX × NRX midpoints produces the virtual array. If the physical TX and RX sub-arrays are designed correctly, these midpoints fall on a uniform grid with element spacing dv = λ/2 (about 1.94 mm at 77 GHz), which is the condition for unambiguous, grating-lobe-free angle estimation.
For a deeper walkthrough of the math behind virtual element positions, see the dedicated article on MIMO virtual array synthesis.
Minimum Redundancy Placement
The classic rule: space the RX elements at d = λ/2 apart, and space the TX elements at NRX × d apart. For a 3 TX / 4 RX azimuth-only system this gives TX spacing of 4 × λ/2 = 2λ ≈ 7.8 mm and RX spacing of λ/2 ≈ 1.94 mm, producing 12 virtual elements on a uniform λ/2 grid. Any deviation from this rule—whether from routing constraints or package pin locations—creates holes or redundancies in the virtual array, degrading sidelobe levels or wasting channels.
Extending to 2-D: Elevation Coverage
For elevation resolution (needed in 4D imaging radar), TX and RX elements must also be offset vertically. A common topology places the TX column with vertical offsets of 0, λ/2, and λ while the RX row remains in a single horizontal line. The resulting virtual array is an L-shaped or filled rectangular grid. Devices with higher channel counts—such as the Cascaded AWR2243 with 12 TX / 16 RX—can form a 192-element virtual aperture, but the PCB layout challenge scales with it.
Orthogonal Waveform Strategies
The virtual array only works if the receiver can separate each TX signal. Three dominant approaches exist:
| Method | How It Works | Trade-off |
|---|---|---|
| Time-Division Multiplexing (TDM) | Only one TX active per chirp; cycle through TXs | Simplest; but frame time scales with NTX, limiting max unambiguous velocity |
| Binary Phase Modulation (BPM) | All TXs transmit simultaneously with Hadamard-coded phase shifts | Full Doppler bandwidth retained; requires 2n TX count for clean separation |
| Frequency-Division Multiplexing (FDM) | Each TX uses a different chirp start frequency offset | Preserves velocity; costs additional IF bandwidth and ADC dynamic range |
TDM is by far the most common in cost-sensitive automotive short- and mid-range radar. BPM and FDM become necessary in long-range or high-velocity scenarios where the Doppler ambiguity of TDM is unacceptable. The waveform choice does not change the PCB antenna layout, but it does affect the digital baseband architecture and the number of ADC channels required.
Antenna Element Design for MIMO Radar PCB
Element Type Selection
At 77 GHz, the most practical on-PCB radiator is the series-fed microstrip patch array (sometimes called a comb-line antenna). Each column of patches forms a single TX or RX element with 10–14 dBi gain in elevation, while the MIMO virtual array handles azimuth beamforming digitally. Typical column lengths are 6–10 patches, with inter-patch spacing of approximately λg (guided wavelength, around 2.4 mm on RO3003 at 77 GHz) to produce a broadside beam.
Material and Stackup Considerations
The antenna layer must sit on a low-loss, tightly tolerance-controlled laminate. Rogers RO3003 (Dk 3.00 ± 0.04, Df 0.0010 at 77 GHz) is the industry standard for automotive radar front-ends. A hybrid stackup bonds the RO3003 antenna core to FR-4 or Megtron-based layers for the digital and power sections. Choosing the right layer count and dielectric combination is covered in detail in the radar PCB stackup guide.
Critical Layout Rules
- Element-to-element spacing accuracy: ±25 µm (±1 mil) or better. At 77 GHz, a 50 µm position error introduces roughly 4.6° of phase error, directly degrading virtual array coherence.
- Feed network isolation: TX and RX feed lines must maintain > 30 dB isolation. Use ground-backed coplanar waveguide (GCPW) with via fences spaced ≤ λ/10 (≈ 0.39 mm) to suppress parallel-plate modes. More on via fence design is available in the via fence and launch design article.
- Symmetry: Keep the TX sub-array and RX sub-array feed networks mirror-symmetric to equalize amplitude and phase across channels.
- Keep-out zones: No copper fill, vias, or components within λ/2 of any radiating edge to avoid pattern distortion.
From Virtual Array to Angular Performance
Angular Resolution
The 3 dB angular resolution of the virtual array is approximately:
Δθ ≈ 0.886 λ / (Nv dv cos θ)
where Nv is the number of virtual elements and dv is the virtual element spacing. For a 12-element λ/2-spaced virtual array at 77 GHz, this gives Δθ ≈ 14.3° at boresight—adequate for short-range automotive applications but insufficient for highway scenarios. Scaling to a 48- or 192-element virtual array (via cascaded transceivers) brings the resolution below 2°, which is the territory of high-channel-count imaging radar boards.
Grating Lobes and Ambiguity
If virtual element spacing exceeds λ/2, grating lobes appear and create phantom targets. This is especially dangerous in TDM-MIMO, where motion between chirps introduces a phase ramp that can shift the grating lobe into the visible region. Mitigation strategies include reducing the chirp-to-chirp interval, applying velocity-disambiguation algorithms in the CFAR detection stage, or switching to BPM waveforms.
Ethernet Magnetics and Digital Interface Layout

Modern MIMO radar modules—especially 4D imaging units with cascaded transceivers—stream large volumes of raw ADC data to an external processor over automotive Ethernet (100BASE-T1 or 1000BASE-T1). The magnetics section of this interface is a common source of radiated emissions that can couple back into the sensitive RX channels if not laid out carefully. Place the Ethernet magnetics as close to the connector as possible, with a solid ground plane underneath and a guard ring of stitching vias. Use the tool below to verify your magnetics placement against standard guidelines.
After running the tool, confirm that the transformer-to-connector distance is under 25 mm and that the differential pair length mismatch is below 2 mil (0.05 mm). On a 77 GHz radar board, even small common-mode currents from the Ethernet PHY can raise the noise floor by several dB if the magnetics layout is sloppy.
MIMO Radar Design Checklist
A complete MIMO radar PCB touches antenna design, RF feed networks, digital baseband, power integrity and mechanical integration. Missing a single item—like forgetting to account for the radome’s dielectric loading on element spacing—can shift the virtual array calibration and degrade angle accuracy. Use the interactive checklist below to build a project-specific review list before taping out.
A good starting checklist for a 3 TX / 4 RX 77 GHz corner radar includes at minimum: virtual array spacing verification, TX-RX isolation measurement plan, feed network phase balance target (± 5° across the band), stackup Dk tolerance confirmation from the laminate vendor, and an over-the-air (OTA) validation step with a corner reflector at known range and angle. For OTA test methodology, refer to the radar test and validation guide.
Common Pitfalls in MIMO Radar Antenna Layout
- Ignoring mutual coupling: Adjacent TX and RX columns couple through surface waves. Full-wave simulation (HFSS, CST) of the entire array—not just a single element—is non-negotiable at 77 GHz.
- Assuming ideal orthogonality: In TDM-MIMO, TX switching transients leak energy into adjacent time slots. Allow a guard interval of at least 5 µs between TX activations.
- Neglecting the radome: A bumper-integrated radome adds dielectric loading that shifts the beam and changes the effective element spacing. Always co-simulate with the radome model. See radar radome integration for details.
- Under-specifying PCB tolerances: Standard Class 2 etching tolerances (± 50 µm) are marginal at 77 GHz. Specify Class 3 per IPC-6012 or tighter, and request impedance coupons on every panel.
Frequently Asked Questions
How many virtual elements does a 3 TX / 4 RX MIMO radar have?
Up to 12 virtual elements, formed by the 3 × 4 = 12 unique TX–RX phase-center midpoints. If the physical antennas are placed with the minimum-redundancy rule (RX at λ/2, TX at NRX × λ/2), all 12 elements fall on a uniform λ/2 grid with no redundancies.
Can MIMO radar work on FR-4 at 77 GHz?
No. FR-4’s dissipation factor (Df ≈ 0.020 at 10 GHz, worse at 77 GHz) and its loose Dk tolerance (± 10 %) make it unsuitable for 77 GHz antenna layers. Low-frequency digital layers in a hybrid stackup can use FR-4, but the antenna and RF feed layers require PTFE or hydrocarbon-ceramic laminates like RO3003 or Isola Astra MT77.
What limits angular resolution in MIMO radar?
Angular resolution is set by the total virtual aperture length (Nv × dv). More TX and RX channels, or wider physical spacing (while keeping dv = λ/2), yield a larger aperture and finer resolution. Practical limits include PCB real estate, transceiver channel count, and the processing power needed for larger FFTs.
TDM vs BPM: which is better for automotive MIMO radar?
TDM is simpler and dominates short- and mid-range sensors. BPM preserves the full unambiguous velocity range and is preferred for long-range forward-facing radar where targets may exceed TDM’s velocity limit. BPM requires more baseband processing and precise TX phase control.
Ready for a quotation?
Send your requirements for a material, stackup and manufacturing review. Price and schedule are confirmed for your project.
