PCB Antenna and Feed Resources

Spiral Antenna Design | Broadband Circular Polarization

A practical guide to spiral antenna design covering Archimedean and equiangular geometries, feed techniques, substrate selection, and PCB fabrication considerations for broadband circular polarization from UHF through millimeter-wave.

Two-arm Archimedean spiral antenna trace on an RF PCB laminate

What Is a Spiral Antenna?

A spiral antenna is a frequency-independent, planar radiator that produces circular polarization over bandwidths exceeding 10:1. Its operating band is set almost entirely by geometry: the outer circumference defines the lowest usable frequency (where the circumference ≈ one wavelength), and the innermost turn sets the upper limit. Because the active radiating zone migrates along the spiral as frequency changes, a single element can cover, for example, 0.5–6 GHz without a matching network—something no patch or dipole can do.

Spiral antennas are workhorses in electronic warfare, direction-finding, wideband radar, radio astronomy, and increasingly in commercial UWB systems. Two dominant geometries exist: the Archimedean spiral and the equiangular (log-spiral). Both are self-complementary when designed as two-arm structures, which forces the input impedance toward the Mushiake constant of approximately 188.5 Ω in free space (≈ 60π Ω).

Archimedean vs. Equiangular Spiral Geometry

Cross-section of spiral antenna with absorber-loaded cavity

Choosing between the two geometries is the first real design decision, and it affects pattern shape, bandwidth flatness, and fabrication complexity.

Parameter Archimedean Spiral Equiangular (Log) Spiral
Arm equation r = r₀ + aφ (linear growth) r = r₀ · e^(aφ) (exponential growth)
Typical bandwidth 10:1 to 20:1 Theoretically infinite; practically 20:1+
Pattern stability Very stable broadside beam Slightly wider beamwidth variation
Impedance constancy Excellent above first resonance Excellent; truly frequency-independent
Fabrication Easier—constant line width & gap Harder—continuously varying width
Common use DF, EW, UWB comms Wideband radar, radio astronomy

For most PCB-based designs below 18 GHz, the Archimedean spiral is preferred because its constant arm width and gap simplify etching tolerances and impedance control. The equiangular form is worth the extra layout effort when you need the widest possible bandwidth or when the pattern must remain self-similar across decades of frequency.

Key Design Parameters

Outer Radius and Low-Frequency Limit

The lowest operating frequency f_low satisfies C_outer ≈ λ_low, giving the outer radius as r_outer ≈ c / (2π · f_low). For a 1 GHz low-end, that is roughly 48 mm. Truncating the spiral smaller raises f_low and degrades axial ratio at the band edge.

Inner Radius and High-Frequency Limit

The feed region’s inner radius sets f_high by the same circumference rule: r_inner ≈ c / (2π · f_high). A 6 GHz upper limit demands r_inner ≤ 8 mm. In practice, the feed structure (balun pad, via transition) often limits how small the inner radius can be, capping the upper frequency before the spiral geometry itself does.

Number of Turns and Arm Width

More turns push f_low down for a given outer radius but increase ohmic loss and inter-arm coupling. Three to five turns usually suffice for a 10:1 bandwidth. Arm width w and gap g are typically equal (self-complementary condition), and their sum equals the arm-to-arm pitch. A common starting point is w = g = 0.5–1.0 mm for an L-/S-band spiral on a standard RF laminate.

Input Impedance and Balun Design

The self-complementary two-arm spiral presents roughly 188 Ω, which must be transformed to 50 Ω for most receiver front-ends. Options include:

  • Infinite balun (tapered microstrip): A microstrip line runs along one arm on the back side of the substrate, gradually transitioning impedance. Simple, but bandwidth depends on taper length.
  • Marchand balun: Compact, well-suited to PCB; achievable 4:1 bandwidth with good amplitude and phase balance.
  • Printed wideband balun on a separate layer: Stripline or broadside-coupled structure embedded in the stackup, common in multilayer RF boards.

Verifying the feed’s return loss across the full band is critical. Use the techniques in the S11 and VSWR measurement guide to catch balun-induced mismatch that simulation may underestimate.

Substrate and Stackup Considerations

The dielectric beneath a spiral antenna is not neutral—it concentrates the radiation toward the substrate side, which is the opposite of what most designs want. Key material and stackup decisions:

  • Dielectric constant (Dk): Lower Dk keeps the wave velocity closer to free space, preserving pattern symmetry. Rogers RO4003C (Dk 3.38) or RO4350B (Dk 3.48) are popular compromises between cost and performance. PTFE laminates (Dk ≈ 2.2) give better pattern symmetry but are harder to process.
  • Substrate thickness: Thicker substrates (30–60 mil / 0.76–1.52 mm) improve low-frequency radiation efficiency but increase surface-wave excitation at higher frequencies. A 20 mil (0.51 mm) laminate is a reasonable middle ground for a 1–6 GHz spiral.
  • Cavity or absorber backing: A bare ground plane behind the spiral creates a resonant cavity that destroys wideband performance. The standard fix is a lossy cavity—a metal cup filled with RF absorber—typically λ_low / 4 deep. For PCB-only solutions, resistive-sheet loading or a frequency-selective surface (FSS) reflector can flatten the gain over a 3:1 to 5:1 sub-band.

These substrate trade-offs are similar to those encountered in UWB PCB antenna design, where broadband impedance and pattern control compete with board-level integration constraints.

Full-Wave Simulation Workflow

Spiral antennas are inherently 3-D electromagnetic problems—the traveling-wave current distribution and cavity interaction cannot be captured by circuit models. A rigorous antenna simulation workflow in HFSS, CST, or FEKO should include:

  1. Parameterize the spiral curve (growth rate, arm width, number of turns, inner/outer radii) so you can sweep trade-offs.
  2. Model the feed realistically: include the balun geometry, not just a lumped port, to capture feed-induced pattern tilt.
  3. Include the cavity or absorber: use measured material properties (μ″, ε″) for the absorber; a perfect-absorber boundary underestimates loss.
  4. Sweep frequency in fine steps (50–100 MHz increments across a decade) and monitor axial ratio, gain, and S11 simultaneously.
  5. Check mesh convergence at both the lowest and highest frequencies—the mesh that converges at 1 GHz is far too coarse at 6 GHz.

Expect 5–7 dBi broadside gain from a two-arm Archimedean spiral over an absorber-loaded cavity across most of the operating band, dropping 1–2 dB near the band edges. Axial ratio should stay below 3 dB across the design bandwidth if the spiral is well-balanced and the feed is symmetric.

Measuring Spiral Antenna Performance

Four-arm spiral antenna PCB on PTFE substrate with SMA connector

Because spiral antennas are circularly polarized and wideband, measurement requires a reference antenna (typically a standard-gain horn with a known axial ratio) and a facility capable of polarization-resolved pattern cuts. Key measurements:

  • Axial ratio vs. frequency: The most sensitive indicator of spiral balance. Degradation above 3 dB usually points to feed asymmetry or truncation effects.
  • Gain vs. frequency: Expect a gradual roll-off at both band edges; a sharp dip mid-band indicates cavity resonance or substrate-mode coupling.
  • Radiation pattern cuts in two orthogonal planes at multiple frequencies—check that the broadside beam stays centered and the beamwidth varies smoothly.

Detailed procedures for gain, beamwidth, and null extraction are covered in the antenna pattern measurement reference. For spiral antennas specifically, always measure both RHCP and LHCP components to compute axial ratio from the pattern data, rather than relying on a single spinning-linear cut.

Design Change ROI: When to Redesign vs. Tolerate

Spiral antenna projects often hit a point where measured axial ratio or gain at a band edge is marginal. Before committing to a board respin—new artwork, new absorber geometry, new balun—estimate whether the performance delta justifies the cost and schedule impact. Enter your current and target specs below to quantify the trade-off.

Loading Design Change ROI…

For example, if your axial ratio at 800 MHz is 4.5 dB against a 3 dB spec, increasing the outer radius by 15 % and re-laying the feed may cost one additional prototype cycle (2–3 weeks, a few hundred dollars in quick-turn RF boards). The calculator helps you weigh that against accepting the degraded polarization purity, which in a direction-finding application could mean several degrees of bearing error—often unacceptable. In a commercial IoT link-budget scenario, 1.5 dB of axial-ratio excess may be absorbed by system margin, making the respin unnecessary.

PCB Fabrication and Tolerance Notes

Spiral antennas are geometrically simple but demand tight process control in a few specific areas:

  • Etch uniformity: Arm width variation directly unbalances the two arms, degrading axial ratio. Hold ±0.5 mil (±12.7 µm) or better on arm width across the full spiral diameter.
  • Registration: If the balun is on an inner layer or the back side, layer-to-layer registration must be ≤ 2 mil (50 µm) to keep the feed centered.
  • Surface finish: ENIG is standard for low contact resistance at the SMA or connector interface. Immersion silver is acceptable if cost is a concern, but watch for tarnish on exposed spiral arms that sit in the radiating aperture.
  • Absorber integration: If the absorber-loaded cavity is part of the assembly, specify the cavity depth tolerance and absorber compression in the drawing. A 10 % change in cavity depth shifts the low-end gain notch by a similar percentage in frequency.

Transitioning from prototype to volume production introduces additional yield concerns around etch uniformity and absorber placement. The antenna prototype-to-production guide covers tolerance budgeting and acceptance criteria for these steps.

Design Checklist for Spiral Antennas

Use the interactive checklist below to track every critical parameter before releasing your spiral antenna design for fabrication. Enter your frequency range, substrate, arm dimensions, and feed type to generate a tailored review list.

Loading Design Checklist Builder…

A completed checklist should confirm at minimum: outer radius satisfies the low-frequency circumference rule, inner radius and feed geometry support the upper frequency, arm width and gap maintain self-complementarity, balun type is validated in simulation across the full band, cavity depth and absorber material are specified with tolerances, and the surface finish is compatible with the connector and environment. Missing any one of these items is the most common root cause of first-spin failures in spiral antenna boards.

Frequently Asked Questions

What bandwidth can a spiral antenna achieve?

A well-designed two-arm Archimedean or equiangular spiral routinely covers 10:1 bandwidth (e.g., 0.5–5 GHz). Bandwidths of 20:1 or more are achievable with careful feed design and absorber-loaded cavities, limited mainly by the physical size of the outer and inner radii.

Why does a spiral antenna produce circular polarization?

The traveling-wave current on the spiral arms radiates most strongly where the arm circumference equals one wavelength. At that annular ring, the current traces a circular path, naturally producing circular polarization. A two-arm spiral fed with equal amplitude and 0°/180° phase gives pure CP; a four-arm spiral can generate sum and difference patterns simultaneously.

Can I put a ground plane directly behind a spiral antenna?

A solid ground plane at a fixed distance creates a resonant cavity that reflects the back-radiation with frequency-dependent phase, destroying the wideband impedance match and pattern. Use an absorber-loaded cavity, a resistive card, or an engineered FSS reflector instead. A ground plane is acceptable only if you need narrowband operation (≤ 2:1 bandwidth).

What is the typical gain of a PCB spiral antenna?

Over an absorber-loaded cavity, expect 5–7 dBic broadside gain across most of the operating band. Without a cavity (free-standing spiral), gain drops to roughly 2–4 dBic because half the power radiates to the back. Gain falls at both band edges where truncation and feed effects dominate.

How do I feed a 188 Ω spiral from a 50 Ω source?

The most common PCB-compatible approach is an infinite balun: a microstrip trace on the back of the substrate follows one spiral arm, tapering from 50 Ω at the connector to the spiral’s characteristic impedance at the center. Marchand baluns and IEEE-documented hybrid-coupler feeds are alternatives when tighter amplitude/phase balance is needed.

Ready for a quotation?

Send your requirements for a material, stackup and manufacturing review. Price and schedule are confirmed for your project.

Upload Gerber