
What Does a Wilkinson Calculator Solve?
A Wilkinson calculator computes the quarter-wave branch impedance and isolation resistor value needed for a matched, isolated power divider at a given center frequency and system impedance. For a standard 2-way equal-split Wilkinson divider with system impedance Z₀, the branch impedance is Z₀√2 (≈ 70.71 Ω for 50 Ω systems) and the isolation resistor is 2 × Z₀ (100 Ω for 50 Ω). The calculator extends this to N-way designs and converts electrical length into physical trace width and length on your chosen substrate.
2-Way Equal-Split Wilkinson: Core Equations

Ernest Wilkinson’s 1960 paper established the elegantly simple topology: two quarter-wave transmission-line arms connect a common input to two isolated output ports, with a lumped resistor bridging the outputs. The design equations for an equal-split divider at center frequency f₀ are:
- Branch impedance: Z_branch = Z₀ × √2
- Isolation resistor: R = 2 × Z₀
- Quarter-wave physical length: L = c / (4 × f₀ × √ε_eff), where ε_eff is the effective dielectric constant of the transmission-line mode
At 50 Ω the branch lines are 70.71 Ω and the resistor is 100 Ω. At 75 Ω (common in CATV), the branch lines become 106.07 Ω and the resistor 150 Ω. The divider is inherently lossless at center frequency—insertion loss is ideally 3.01 dB per arm (the power-split ratio), with no dissipative loss in the resistor under balanced conditions.
Bandwidth and Return Loss
A single-section Wilkinson typically delivers better than 20 dB return loss and 20 dB isolation over roughly a 40–50 % fractional bandwidth. If you need wider bandwidth, cascade two or three quarter-wave sections with tapered impedances and multiple isolation resistors. Each added section extends usable bandwidth by roughly 20–30 percentage points at the cost of board area and tighter fabrication tolerances.
N-Way Wilkinson Divider Equations
For an N-way radial (star) Wilkinson divider where all ports share a common junction, the branch impedance and inter-port isolation resistors change:
- Branch impedance: Z_branch = Z₀ × √N
- Isolation resistor between adjacent ports: R = N × Z₀ (for a planar radial topology with nearest-neighbor resistors)
A 3-way divider in 50 Ω therefore needs 86.60 Ω branches and 150 Ω resistors; a 4-way needs 100 Ω branches and 200 Ω resistors. Beyond 4 ways, the radial geometry becomes difficult to lay out on a single layer, so most designers prefer a corporate (binary-tree) divider architecture built from cascaded 2-way stages—each stage uses the familiar 70.71 Ω / 100 Ω values, and the total insertion loss is 3.01 dB per division level (6.02 dB for a 4-way, 9.03 dB for an 8-way, plus conductor and dielectric losses).
From Impedance to Trace Geometry
Once the calculator returns Z_branch, you need a physical microstrip or stripline width and length on your PCB substrate. The critical inputs are:
- Substrate Dk (dielectric constant): e.g., RO4350B at Dk 3.48, or standard FR-4 at ≈ 4.3–4.5
- Substrate height (h): common values are 10 mil (0.254 mm), 20 mil (0.508 mm), or 30 mil (0.762 mm)
- Copper thickness: typically 0.5 oz (17.5 µm) or 1 oz (35 µm)
For a 70.71 Ω microstrip on 20 mil RO4350B (Dk 3.48), the trace width works out to roughly 22 mil (0.56 mm)—narrower than the 45 mil needed for 50 Ω on the same substrate. This is important: the branch traces are noticeably thinner than the input and output 50 Ω lines, so you need a smooth taper at each junction to minimize parasitic discontinuity capacitance. Our RF PCB stackup builder can help you verify the dielectric height and copper weight before you commit to a laminate.
Choosing the right laminate matters. A low-loss material like Rogers RO4350B (Df ≈ 0.0037 at 10 GHz) keeps dissipative loss in the quarter-wave arms below 0.1 dB at C-band, while standard FR-4 (Df ≈ 0.020) would add 0.3–0.5 dB per arm at the same frequency. Consult the RF PCB material selection guide for a full Dk/Df comparison across common laminates.
Isolation Resistor Placement on the PCB
The isolation resistor must sit symmetrically between the two output ports, with its pads connected as close to the electrical midpoint of the output traces as possible. Practical tips:
- Use a thin-film chip resistor (0402 or 0201 at frequencies above 6 GHz) to minimize parasitic inductance. A 0603 body adds roughly 0.4 nH of series inductance, which degrades isolation above 4–5 GHz.
- Keep via stubs short if the resistor ground pads need vias; better yet, use surface-mount pads directly on the microstrip layer.
- For detailed placement strategies and EM-simulation results, see the Wilkinson divider design guide.
Unequal-Split Wilkinson Dividers

Not every application needs an equal 3 dB split. An unequal Wilkinson divides power in a ratio K² : 1 by using two different branch impedances:
- Z₁ = Z₀ × √(K × (1 + K²)) — arm to the lower-power port
- Z₂ = Z₀ × √((1 + K²) / K) — arm to the higher-power port (note: this arm is lower impedance, hence wider)
- R = Z₀ × (K + 1/K)
For a 2:1 power ratio (K = √2), the arms become 86.6 Ω and 57.7 Ω, and R = 122.5 Ω. The unequal-split divider design page walks through impedance-step transitions for these asymmetric topologies.
Design Checklist for a Wilkinson Divider PCB
- Define Z₀, center frequency, and required bandwidth.
- Calculate Z_branch (= Z₀√2 for equal split) and R (= 2Z₀).
- Select substrate material and thickness; compute trace width for Z_branch using a microstrip/stripline solver.
- Calculate quarter-wave physical length from ε_eff at f₀.
- Place the isolation resistor symmetrically; choose a package with low parasitic inductance for your frequency.
- Add tapered transitions between 50 Ω feed lines and the higher-impedance branch lines.
- Simulate S-parameters (S11, S21, S31, S23) across the band; target S11 < −20 dB and isolation > 20 dB at f₀.
- Verify manufacturability: minimum trace width, spacing, and via-to-pad clearance per your fabricator’s capability.
From Design to Fabrication
After finalizing the layout, understanding the PCB manufacturing process helps you specify the right fabrication notes—especially for RF boards that require tight impedance control (±5 % or better on the 70.71 Ω branches). The flow below outlines each production step from lamination through final electrical test.
Pay particular attention to the etch-compensation step: because the branch lines are narrower than standard 50 Ω traces, over-etching by even 0.5 mil shifts the impedance by 1–2 Ω, which directly degrades return loss. Specify controlled-impedance fabrication with coupon verification on the same panel.
Frequently Asked Questions
What is the insertion loss of an ideal 2-way Wilkinson divider?
Exactly 3.01 dB per output port, representing the inherent power split. Any loss above 3.01 dB is dissipative loss from conductor resistance, dielectric absorption, and radiation—typically 0.1–0.5 dB depending on frequency and substrate.
Can I build a Wilkinson divider on FR-4?
Yes, for frequencies up to about 2–3 GHz. Above that, FR-4’s high Df (≈ 0.020) and poorly controlled Dk (±10 %) add excess loss and shift the center frequency unpredictably. Switch to a controlled-Dk laminate like RO4350B or Isola Astra MT77 for designs above 3 GHz.
How do I extend the bandwidth of a Wilkinson divider?
Use a multi-section design: two cascaded quarter-wave sections with different impedances and two isolation resistors can achieve 20 dB return loss over a full octave bandwidth. Three sections push this to nearly a decade. The trade-off is board area and more resistors to place accurately. Refer to the Wilkinson power divider overview on Wikipedia for the multi-section impedance taper equations.
Why does isolation degrade at high frequency?
Parasitic inductance in the isolation resistor and asymmetry in the output traces break the balanced condition that keeps the resistor from dissipating power. At millimeter-wave frequencies (above 30 GHz), designers often replace the lumped resistor with a thin-film resistive element integrated directly into the substrate, or use a distributed resistive section along the output lines.
What is the difference between a Wilkinson divider and a branchline coupler?
A Wilkinson divider splits power in-phase (0° between outputs) and uses a resistor for isolation. A branchline coupler produces a 90° phase difference between outputs and achieves isolation through its four-port hybrid topology—no resistor needed. Use our branchline coupler calculator to compare dimensions and performance. The branchline coupler is preferred when you need quadrature outputs (e.g., for I/Q mixers), while the Wilkinson is the standard choice for in-phase power distribution in feed networks and antenna arrays on Rogers laminates.
Ready for a quotation?
Send your requirements for a material, stackup and manufacturing review. Price and schedule are confirmed for your project.
