
What the Cascaded Noise Figure Calculator Does
The cascaded noise figure of an RF receive chain is the single number that tells you how much noise the entire system adds to the signal. It is dominated by the first stage—usually an LNA—and calculated with the Friis noise figure equation. This calculator lets you enter gain and noise figure for each stage in your chain, then returns the overall system noise figure in dB so you can judge whether your receiver meets its sensitivity target.
The Friis formula, expressed in linear (ratio) terms, is:
Ftotal = F1 + (F2 − 1) / G1 + (F3 − 1) / (G1 · G2) + …
where Fn is the noise factor (linear) of stage n and Gn is its available power gain (linear). Converting back to dB gives the system NF you compare against your link budget.
Cascaded Noise Figure Calculator

Enter the noise figure (dB) and gain (dB) for each stage in your receive chain—LNA, filter, mixer, IF amplifier, and so on. The tool applies the Friis equation stage by stage and returns the cumulative noise figure after every block, so you can see exactly where performance degrades.
A typical result: an LNA with 0.8 dB NF and 18 dB gain followed by a band-pass filter with 2.5 dB insertion loss (enter as NF = 2.5 dB, gain = −2.5 dB) and a mixer with 7 dB NF yields a cascaded NF of roughly 1.1 dB. That confirms the LNA’s high gain is suppressing the downstream noise contributions. If you swap the filter ahead of the LNA, the cascaded NF jumps to about 3.3 dB—a 2.2 dB penalty that directly reduces receiver sensitivity. This is why component ordering matters as much as individual specs.
Why the First Stage Dominates
Look at the denominator in each Friis term: every subsequent stage’s excess noise factor (Fn − 1) is divided by the cumulative gain of all preceding stages. A first-stage gain of 20 dB (factor of 100) reduces the second stage’s noise contribution by 20 dB. This is the fundamental reason LNA design focuses so aggressively on minimizing noise figure—even 0.2 dB at the front end can shift system sensitivity by the same amount.
Practical Stage-Ordering Rules
- Place the LNA first whenever system architecture allows. Any passive loss ahead of it (cable, connector, pre-select filter) adds directly to system NF.
- Minimize pre-LNA losses. A 0.5 dB connector-plus-trace loss before a 0.7 dB LNA gives a cascaded NF of at least 1.2 dB—a 70 % increase in noise factor.
- High-gain early stages relax later-stage requirements. After 25 dB of front-end gain, a mixer with 10 dB NF contributes only about 0.03 dB to the cascade.
- Attenuators and filters are “negative-gain” stages. Enter their insertion loss as both NF and negative gain in the calculator to see the true impact.
For a deeper walkthrough of noise factor versus noise figure and how PCB layout choices (ground-via fencing, trace substrate selection) affect measured NF, see the companion article on noise figure fundamentals.
Worked Example: 5.8 GHz Receiver Front End
Consider a four-stage 5.8 GHz ISM-band receiver:
| Stage | Component | NF (dB) | Gain (dB) |
|---|---|---|---|
| 1 | SAW pre-select filter | 1.8 | −1.8 |
| 2 | LNA (e.g., SKY67151-396LF) | 0.6 | 20.0 |
| 3 | Image-reject filter | 2.0 | −2.0 |
| 4 | Mixer + IF amp | 8.0 | 12.0 |
Plugging these into the calculator gives a cascaded NF of approximately 2.5 dB. The 1.8 dB filter loss before the LNA is the largest single penalty. If the system spec requires NF ≤ 2.0 dB, you have two options: move the pre-select filter after the LNA (trading image rejection for noise), or switch to a lower-loss filter technology. This kind of trade-off analysis is exactly what the calculator is for—run both scenarios in seconds.
Connecting Noise Figure to Link Budget

System noise figure feeds directly into receiver sensitivity via:
Sensitivity (dBm) = −174 + 10 log₁₀(BW) + NF + SNRmin
where −174 dBm/Hz is the thermal noise floor at 290 K, BW is the channel bandwidth in Hz, and SNRmin is the minimum signal-to-noise ratio for your modulation. A 1 dB improvement in cascaded NF translates to 1 dB better sensitivity—or equivalently, about 12 % more range in free space.
To close the loop from transmitter EIRP through path loss to that sensitivity number, use the Friis transmission equation calculator below. Enter frequency, distance, and antenna gains to get the received power, then compare it against the sensitivity you derived from the noise figure result above.
For example, at 5.8 GHz over 100 m with 6 dBi antennas on each end, the Friis equation gives a received power near −52 dBm. If your cascaded NF is 2.5 dB and you need 10 dB SNR in a 20 MHz channel, sensitivity is about −88.5 dBm—leaving over 36 dB of link margin. That margin absorbs multipath fading, body blockage, and manufacturing tolerances on the PCB and antenna.
PCB Layout Considerations That Affect Noise Figure
Calculated NF is only as good as the board delivers. Several layout-level choices can add 0.3–1.0 dB of hidden noise degradation:
- Substrate loss tangent (Df). A microstrip feed line on standard FR-4 (Df ≈ 0.020 at 5 GHz) loses roughly 0.35 dB/cm; on RO4350B (Df ≈ 0.0037) the same line loses about 0.08 dB/cm. That difference matters in the few centimeters between the antenna connector and the LNA input. Consult the high-frequency PCB materials guide for loss tangent data across laminates.
- Ground-via spacing. Sparse vias around the LNA ground paddle raise the effective source impedance, shifting the device off its optimum noise match. Keep via pitch below λ/20 at the operating frequency.
- Trace impedance control. An impedance mismatch at the LNA input reflects signal power but also changes the noise match. Use a PCB stackup builder to verify controlled-impedance geometry before routing.
Verifying the Calculated NF on the Bench
Once the board is fabricated, measure the actual cascaded NF using the Y-factor method (a noise source toggled between hot and cold states) or the cold-source/vector-corrected method on a modern noise figure measurement setup. Compare against the Friis prediction: a discrepancy greater than 0.5 dB usually points to unexpected loss in connectors, solder joints, or substrate, or to an impedance mismatch degrading the LNA’s noise match.
Quick Checklist Before Measurement
- Calibrate the noise source ENR at the exact test frequency (ENR tables are frequency-dependent).
- De-embed cable and adapter losses—they add directly to measured NF.
- Bias the LNA at the datasheet-recommended current; NF is sensitive to drain current in GaAs and GaN devices.
- Verify that the DUT is unconditionally stable; oscillation can corrupt NF readings.
Frequently Asked Questions
What is a good noise figure for a receiver?
It depends on the application. Satellite downlink receivers at L-band target 0.5–1.0 dB; Wi-Fi front ends are typically 2–4 dB; cellular base-station receivers aim for 1.5–2.5 dB. The cascaded NF must be low enough that receiver sensitivity meets the link budget with adequate margin.
Can I use the Friis equation for transmit chains?
The Friis noise figure equation applies to any cascade of two-port networks, but it is meaningful only when the noise added by each stage matters—i.e., in receive paths. In a transmit chain, signal levels are high enough that added noise is negligible compared to the carrier, so noise figure is rarely specified for power amplifiers.
Does impedance mismatch affect noise figure?
Yes. The Friis equation assumes matched conditions. A mismatch at the LNA input changes the source impedance seen by the device, moving it away from its minimum-noise impedance (Γopt). The resulting NF increase is described by the noise parameters model (Fmin, Rn, Γopt). Proper noise matching—often a deliberate trade-off against gain match—is central to LNA input network design.
How do I enter a passive component like a filter into the calculator?
A passive, reciprocal component at the reference temperature has a noise figure equal to its insertion loss. Enter both NF and gain as the insertion loss value—NF positive, gain negative. For example, a filter with 3.0 dB insertion loss: NF = 3.0 dB, Gain = −3.0 dB.
Ready for a quotation?
Send your requirements for a material, stackup and manufacturing review. Price and schedule are confirmed for your project.
