
What Is a 4-Layer PTFE Multilayer Stackup?
A 4-layer PTFE multilayer stackup is a printed-circuit-board construction that uses two or more sheets of polytetrafluoroethylene-based laminate—such as Rogers RT/duroid 5880 (Dk 2.20 ± 0.02) or RT/duroid 6002 (Dk 2.94 ± 0.04)—bonded into a single board with four copper layers and three dielectric intervals. Because PTFE cannot be pressed with conventional FR-4 prepreg, the layers are joined by fusion bonding (a thermoplastic reflow of the PTFE itself) or by thin thermoplastic bond films. This architecture is the workhorse for filters, couplers, feed networks and multilayer RF PCBs operating from S-band through Ka-band.
Why PTFE—and Why It Needs Special Bonding

PTFE laminates dominate microwave design because of their ultra-low dissipation factor (Df 0.0009–0.0021 at 10 GHz for the duroid family) and tight Dk tolerance. But PTFE’s low surface energy—around 18–20 mN/m—means epoxy prepreg will not wet or adhere to it reliably. Two practical bonding routes solve this problem:
- Fusion bonding. The PTFE surfaces are plasma-etched or sodium-naphthalene treated, stacked, and pressed at 370–380 °C so the PTFE reflows and fuses across the interface. No foreign adhesive enters the RF path. The result is an all-PTFE dielectric with uniform Dk from layer to layer—critical when a stripline filter must hold ±1 % impedance.
- Thermoplastic bond film. A thin (25–75 µm / 1–3 mil) FEP or PFA film is placed between cores. It melts at ≈ 260–305 °C, below PTFE’s melt point, and forms a mechanically strong joint. The bond-ply Dk is typically 2.05–2.15, close to many PTFE substrates, so impedance perturbation is small but must be modeled.
For a deeper look at process limits, temperature profiles, and yield considerations, see the companion article on fusion bonding PTFE multilayers.
Reference 4-Layer Stackup: Fusion-Bonded RT/duroid 5880
The table below shows a representative build used in X-band and Ku-band stripline circuits. All copper is ½ oz (17.5 µm) electrodeposited, and the finished board thickness targets 62 mil (1.57 mm).
| Layer | Material | Thickness (mil) | Dk @ 10 GHz | Function |
|---|---|---|---|---|
| L1 (Top) | Copper | 0.7 | — | Microstrip / component pads |
| Core 1 | RT/duroid 5880 | 20 | 2.20 | Microstrip dielectric |
| L2 | Copper | 0.7 | — | Ground / stripline ref |
| Bond | Fusion (PTFE reflow) | 2–4 | 2.20 | Interlayer bond |
| L3 | Copper | 0.7 | — | Stripline signal |
| Core 2 | RT/duroid 5880 | 20 | 2.20 | Stripline dielectric |
| L4 (Bot) | Copper | 0.7 | — | Ground |
Because the fusion bond layer is the same PTFE polymer as the cores, the effective Dk seen by the L3 stripline is 2.20 across the full cross-section—no asymmetric Dk correction is needed. When a bond film is used instead, the 25 µm FEP layer (Dk ≈ 2.10) sits between L2 and L3; the weighted average Dk shifts by roughly 0.5 %, which matters above 30 GHz and should be captured in the EM model.
Use the interactive stackup designer below to adjust core thicknesses, copper weights, and dielectric constants for your own frequency plan. Enter your target impedance and total thickness, then compare the predicted trace widths against your layout constraints.
If the tool returns a 50 Ω microstrip width of about 56 mil on 20 mil duroid 5880 (Dk 2.20, ½ oz copper), that is consistent with published Rogers data within ±1 mil. A stripline on the same substrate pair will be narrower—roughly 18–20 mil for 50 Ω—because it is enclosed between two ground planes. Confirm both values in a 2.5-D field solver before releasing Gerbers.
Choosing Between Fusion Bond and Film Bond
Neither method is universally better. The right choice depends on frequency, volume, and mechanical requirements.
| Criterion | Fusion Bond | Thermoplastic Film Bond |
|---|---|---|
| Dk uniformity across bond | Identical to core | Slight offset (ΔDk ≈ 0.05–0.10) |
| Press temperature | 370–380 °C | 260–305 °C |
| Copper adhesion risk | Higher—PTFE reflow can lift pads | Lower—film acts as cushion |
| Reflow flatness | Tighter process window | More forgiving |
| Best use case | Stripline filters, phase-matched networks above 20 GHz | General multilayer, mixed-signal boards, cost-sensitive builds |
Choose fusion bonding when the circuit lives entirely in stripline and Dk homogeneity is the top priority. Choose film bonding when you need wider process margins, especially on larger panels or boards that include both RF and low-frequency control layers. For designs that pair PTFE cores with different Dk values on different layers—say, duroid 5880 on the antenna side and RO4003C on the digital side—refer to the mixed-Dk stackup guide.
Via Design and Annular Ring Rules in PTFE Multilayers

PTFE’s softness and high coefficient of thermal expansion in Z (CTE-z around 200–280 ppm/°C for unreinforced grades, vs. 40–70 ppm/°C for woven-glass-reinforced versions like RO3003) make via reliability the single biggest risk in a PTFE multilayer. Key rules:
- Drill-to-copper clearance. Start with a minimum 5 mil annular ring on inner layers and 7 mil on outer layers per IPC-6012 Class 3. PTFE’s tendency to smear during drilling can erode the effective ring, so many fabricators add 1–2 mil margin beyond the IPC minimum.
- Drill diameter. Prefer mechanical drilling with a fresh carbide bit at reduced feed rates (≤ 0.05 mm/rev). Laser drilling is possible for microvias in glass-reinforced PTFE but impractical in unreinforced grades because the PTFE chars rather than ablates cleanly.
- Plating. Electroless copper adhesion to PTFE hole walls requires aggressive plasma desmear (CF₄/O₂ mix) followed by a permanganate or sodium etch. Skipping this step is the number-one cause of barrel cracks in PTFE multilayers.
- Back-drilling. On 4-layer PTFE boards the stub length from a through-hole via is short enough (≤ 40 mil) that back-drilling is rarely needed below 20 GHz. Above that, consider blind or buried vias to eliminate the stub entirely.
Check your pad and hole dimensions against the annular ring calculator below. Enter your finished hole size, pad diameter, and the fabricator’s drill tolerance (typically ±3 mil for PTFE) to verify you meet Class 3 minimums.
For example, a 12 mil finished hole with an 24 mil pad and ±3 mil drill wander yields a worst-case annular ring of (24 − 12)/2 − 3 = 3 mil—below the 5 mil Class 3 inner-layer minimum. Bumping the pad to 28 mil restores the ring to 5 mil. This is a common trap when migrating a design from FR-4 (where drill wander is tighter) to PTFE.
Layer-to-Layer Registration
PTFE cores are dimensionally less stable than FR-4 during lamination. Unreinforced PTFE can shrink 1–3 mil/inch in X-Y during the 370 °C fusion cycle, compared with 0.3–0.7 mil/inch for glass-reinforced grades. This directly impacts layer-to-layer registration: a 1.5 mil/inch shift across a 12-inch panel means 18 mil of total misregistration if uncompensated.
Fabricators address this with pre-scaling artwork (enlarging inner-layer images to anticipate shrinkage), pinned lamination tooling, and post-etch X-ray verification. When specifying a PTFE multilayer, always ask for the fabricator’s measured shrinkage data on the exact laminate grade you plan to use—generic numbers are not reliable enough for tightly coupled stripline.
Design Checklist for a 4-Layer PTFE Fusion-Bonded Stackup
- Select the PTFE grade based on target frequency and Dk: duroid 5880 (Dk 2.20) for lowest loss, RT/duroid 6002 (Dk 2.94) for smaller trace widths, or RO3003 (Dk 3.00) for glass-reinforced dimensional stability.
- Decide fusion bond vs. film bond based on Dk-uniformity needs and fabricator capability.
- Run impedance synthesis in a 2.5-D solver with the actual bond-layer thickness and Dk—do not assume it is zero.
- Specify annular rings ≥ 5 mil inner / 7 mil outer after worst-case drill wander.
- Require plasma desmear plus permanganate etch on all plated holes.
- Request X-ray registration data at incoming inspection, especially for stripline layers.
- If your design later scales to more layers, review the RF stackup library for 6- and 8-layer PTFE references.
Frequently Asked Questions
Can I fusion-bond more than four PTFE layers?
Yes. Six- and eight-layer fusion-bonded PTFE boards are produced for phased-array feeds and multi-channel receivers. Each additional bond cycle adds cumulative X-Y shrinkage, so glass-reinforced grades (RO3003, RT/duroid 6002) are strongly preferred above four layers to keep registration within spec.
Is fusion bonding compatible with mixed PTFE/FR-4 hybrid stackups?
Not directly. The 370 °C fusion temperature would destroy FR-4 (Tg typically 170–180 °C). Hybrid builds use thermoplastic bond films at ≤ 260 °C or mechanical fastening. For details on combining different dielectrics, see the mixed-Dk stackup article.
What is the maximum operating frequency for a 4-layer PTFE stackup?
Material loss is not the limit—registration and via parasitics are. Fusion-bonded duroid 5880 stackups are routinely used at 40 GHz and have been demonstrated at 77 GHz for automotive radar front-ends, though at millimeter-wave frequencies most designers move to two-layer or thin four-layer builds with blind vias to minimize via stubs.
How much does a 4-layer PTFE multilayer cost compared to FR-4?
Expect roughly 5–10× the bare-board cost of an equivalent FR-4 four-layer, driven by laminate price, slower drilling, plasma desmear, and tighter process controls. Volume, panel utilization, and the specific PTFE grade shift the multiplier significantly—always get a quote on the actual design.
Ready for a quotation?
Send your requirements for a material, stackup and manufacturing review. Price and schedule are confirmed for your project.
