
What RoHS and REACH Mean for RF PCBs
Every RoHS REACH PCB shipped into the EU must satisfy two overlapping chemical-safety regimes at once. RoHS (Restriction of Hazardous Substances, EU Directive 2011/65/EU as amended by 2015/863) limits ten substances in electrical equipment—including lead, cadmium, mercury, hexavalent chromium, PBBs, PBDEs, and four phthalates (DEHP, BBP, DBP, DIBP). REACH (EC 1907/2006) goes further: it requires registration and disclosure of any Substance of Very High Concern (SVHC) present above 0.1 % w/w in any article, with the SVHC Candidate List updated roughly twice a year and now exceeding 240 entries. For RF PCBs, both directives apply simultaneously, and the burden falls on whoever places the finished product on the EU market.
RF boards are more exposed than standard digital designs because their stackups routinely contain PTFE composites, ceramic-filled hydrocarbons, thermoset polyimide, and specialty surface finishes like electroless nickel / immersion gold (ENIG) or immersion silver. Each of these introduces a distinct material chemistry that must be traced back to a compliant raw-material declaration. A single non-compliant sub-component—an older tin-lead finish on an edge-launch connector pad, a legacy flux residue, or a filler additive on the SVHC list—can block market access for the entire assembly.
RoHS REACH PCB Substance Limits in Fabrication

| Substance | Maximum Concentration (by weight in homogeneous material) | Where It Appears in RF PCBs |
|---|---|---|
| Lead (Pb) | 0.1 % | Solder, HASL finish, component terminations |
| Cadmium (Cd) | 0.01 % | Some older plating baths, pigments |
| Mercury (Hg) | 0.1 % | Rarely in PCBs; legacy switches |
| Hexavalent chromium (Cr⁶⁺) | 0.1 % | Passivation layers on metal housings |
| PBB / PBDE | 0.1 % | Flame retardants in some resin systems |
| DEHP, BBP, DBP, DIBP (phthalates) | 0.1 % each | Plasticisers in cable insulation, conformal coatings |
The “homogeneous material” rule matters: RoHS evaluates each distinct material layer separately. In a six-layer RF stackup with two different dielectric types plus copper foil, prepreg, solder mask, and surface finish, every layer is a separate homogeneous material. A lead-free ENIG finish can be compliant even if the underlying copper foil uses a different supplier, as long as each layer individually stays below the threshold. Understanding this layer-by-layer logic is essential to building a defensible RoHS REACH PCB documentation package.
REACH and the SVHC Candidate List
REACH obligations differ from RoHS in two important ways. First, the list of controlled substances is much larger and grows continuously—ECHA’s SVHC Candidate List is the authoritative reference. Second, the duty is not just restriction but disclosure: if any SVHC exceeds 0.1 % w/w in an article, the supplier must inform the recipient within 45 days of a consumer request. For RF PCB manufacturers, this means maintaining a living material declaration database, not a one-time certificate.
Substances on the Candidate List that occasionally surface in PCB supply chains include certain borates (used in some glass-weave treatments), lead monoxide (in older ceramic fillers), and medium-chain chlorinated paraffins (MCCPs, sometimes found in PVC cable sheathing shipped alongside boards). PTFE itself is not an SVHC, but some processing aids historically used to manufacture PTFE sheet—such as PFOA—are now restricted under REACH Annex XVII (entry 68). Fabricators sourcing PTFE laminates should verify the supplier’s PFOA-free declaration, especially for older stock.
RF Laminate Materials and RoHS REACH PCB Challenges
Choosing an RF PCB laminate involves balancing Dk, Df, thermal stability, and now regulatory status. Most major laminate vendors—Rogers, Isola, Taconic, Arlon—publish full material declarations and RoHS certificates on their websites. The real risk lies elsewhere:
- Hybrid stackups. Mixing a Rogers RO4350B core with standard FR-4 prepreg means two separate supplier declarations must cover the same board. If the FR-4 prepreg uses a brominated flame retardant, confirm it is not a restricted PBB/PBDE variant.
- Ceramic fillers. High-Dk ceramic-loaded PTFE laminates (used in PTFE and hydrocarbon designs) may contain barium titanate or other fillers whose raw material sourcing must be traced for SVHC content.
- Legacy stock. A laminate sheet manufactured before a supplier switched to a PFOA-free process may still be sitting in a distributor’s warehouse. Lot-level traceability is the only reliable safeguard, and verifying material authenticity is part of that chain.
- Surface finishes. Immersion tin, ENIG, and OSP are all lead-free by design. HASL is available in both SnPb (non-RoHS) and lead-free SAC alloy versions—specify explicitly on the fabrication drawing.
Arlon Laminates and Compliance
Arlon (now part of Rogers Corporation) produces ceramic-filled PTFE and thermoset laminates widely used in aerospace and defense RF designs. Products like the CLTE-XT and AD series carry full RoHS declarations. When selecting an Arlon grade, check both the electrical properties and the current REACH declaration date—some product lines were reformulated during the PFOA phase-out. Use the selector below to narrow Arlon grades by Dk, Df, and frequency range, then cross-reference the vendor’s published compliance certificate.
For example, selecting CLTE-XT (Dk 2.94, Df 0.0012 at 10 GHz) returns a laminate well-suited to phased-array feeds up through Ku-band. Its current datasheet confirms RoHS compliance and lists no SVHCs above 0.1 %. If you are designing for a program with additional halogen-free or sustainability requirements, note that CLTE-XT’s flame-retardant system is non-halogenated—an advantage for IEC 61249-2-21 compliance as well.
Building a Compliant RoHS REACH PCB Declaration Package

A complete RoHS/REACH declaration for an RF PCB assembly typically includes:
- Laminate RoHS certificate — from each dielectric supplier, referencing the specific product code and revision date.
- Copper foil declaration — usually covered by the laminate vendor, but verify separately for specialty foils (reverse-treated, low-profile).
- Surface finish specification — stating the alloy composition (e.g., ENIG: Ni 3–6 µm / Au 0.05–0.10 µm, lead-free).
- Solder paste / solder bar certificate — SAC305 (Sn96.5/Ag3.0/Cu0.5) is the dominant lead-free alloy.
- Solder mask and legend ink declarations — confirm no restricted phthalates or PBBs in the cured film.
- REACH SVHC disclosure — a statement listing any SVHCs above 0.1 % w/w, or confirming none are present, dated after the most recent Candidate List update.
- Full material declaration (FMD) — increasingly requested by aerospace and automotive OEMs, conforming to IPC-1754 or IPC-1752A format.
The assistant below walks through RoHS and REACH applicability for your specific board, flagging which documents you need based on the materials and finishes you select.
After running the tool, you might find, for instance, that a six-layer hybrid stackup with RO4350B cores and Megtron 6 prepreg requires two separate laminate declarations, one surface-finish certificate for ENIG, and a REACH SVHC statement dated no earlier than January 2025 (the most recent Candidate List update at time of writing). Missing any one of these can stall a shipment at EU customs or trigger a product recall notification through RAPEX. A thorough RoHS REACH PCB documentation set is your best insurance against these disruptions.
Common Pitfalls and How to Avoid Them
Assuming “Lead-Free” Equals “RoHS Compliant”
Lead-free soldering addresses only one of ten restricted substances. A board assembled with SAC305 but coated in a solder mask containing a restricted phthalate plasticiser is still non-compliant. Always request the full RoHS substance declaration, not just a lead-free statement.
Outdated REACH Declarations
Because the SVHC Candidate List is updated in January and July each year, a REACH declaration from 18 months ago may not cover substances added in the interim. Best practice: require suppliers to reconfirm within 60 days of each Candidate List update, or at minimum once per calendar year.
Exemptions That Expire
RoHS grants time-limited exemptions for certain uses of lead—for example, Exemption 7(a) allows lead in high-melting-point solders (>85 % Pb) used in some flip-chip and die-attach processes. These exemptions have expiry dates and are periodically reviewed. If your RF module relies on an exemption, track its renewal status through the EU’s RoHS exemption review process and have a lead-free fallback qualified.
Mixed Military / Commercial Builds
Military and space hardware is exempt from RoHS under Directive 2011/65/EU Article 2(3), but REACH still applies to articles manufactured or imported into the EU regardless of end use. A space-qualified RF board shipping through an EU distributor must still carry REACH SVHC disclosure. This catches many defense contractors off guard.
Checklist: RoHS REACH PCB Compliance for Your Next RF Order
- Specify “RoHS compliant per 2011/65/EU + 2015/863” on the fabrication drawing—not just “lead-free.”
- Request laminate-level RoHS certificates by product code and lot number.
- Confirm surface finish alloy composition in writing; reject generic “lead-free HASL” without an alloy call-out.
- Obtain a REACH SVHC declaration dated after the most recent Candidate List update.
- For IPC-1754 or IPC-1752A full material declarations, allow 2–4 weeks lead time—fabricators often need to collect sub-supplier data.
- If relying on a RoHS exemption, document the exemption number, expiry date, and fallback plan.
- Archive all declarations with the production lot; EU market surveillance authorities can request them years after sale.
Frequently Asked Questions
Is PTFE laminate RoHS compliant?
Yes. Pure PTFE and filled-PTFE laminates from major vendors (Rogers, Taconic, Arlon) are RoHS compliant. The concern is not PTFE itself but processing aids like PFOA, which are restricted under REACH Annex XVII. Current-production laminates have transitioned to PFOA-free processes; verify the lot date and supplier declaration.
Do I need both RoHS and REACH certificates for an RF PCB?
They serve different purposes. A RoHS declaration confirms ten specific substances are below threshold in the finished product. A REACH SVHC disclosure covers a much broader and evolving list of substances. Products sold in the EU need both, making a complete RoHS REACH PCB package essential for market access.
Does RoHS apply to RF PCB prototypes?
If the prototype is part of equipment that will be placed on the EU market, yes. Prototypes used solely for R&D evaluation and never sold or distributed are generally outside scope, but the line is narrow—consult your regulatory team.
What surface finish is safest for RoHS compliance?
ENIG, immersion silver, immersion tin, and OSP are all inherently lead-free. ENIG is the most common choice for RF boards because it also provides a flat, solderable, and corrosion-resistant surface compatible with wire bonding and press-fit connectors.
Can a fabricator provide a single declaration for the whole board?
Many fabricators issue a board-level RoHS and REACH statement, but this is only as reliable as the sub-supplier data behind it. For critical programs, request laminate-level and chemistry-level certificates and audit the supply chain at least annually.
Ready for a quotation?
Send your requirements for a material, stackup and manufacturing review. Price and schedule are confirmed for your project.
