Radar PCB Design and Review Resources

Radar Antenna Array Layout | Series Fed Patch

A practical guide to radar antenna array layout focusing on series-fed patch design at 77 GHz, covering element spacing, feed-line impedance tapering, beam squint mitigation, and PCB fabrication constraints.

Series-fed patch antenna array on a 77 GHz radar PCB

What Is a Radar Antenna Array?

A radar antenna array is a set of radiating elements—most commonly microstrip patches—arranged in a defined geometry on a PCB so their individual fields combine to form a directive beam. At 77 GHz automotive radar frequencies the free-space wavelength is roughly 3.9 mm, which means the entire array, feed network, and MMIC launch can fit on a board smaller than a credit card. Series-fed patch arrays dominate this space because they need only a single microstrip line to excite every element, eliminating the complex power-divider trees that corporate-fed designs require.

The rest of this article walks through the layout decisions that determine whether a series-fed radar antenna array actually hits its gain, sidelobe, and bandwidth targets once fabricated.

Series-Fed vs. Corporate-Fed Topologies

Cross-section of a two-layer radar antenna PCB stackup

Choosing between a series feed and a corporate (parallel) feed is the first architectural decision. Each topology shapes the array’s bandwidth, beam-pointing stability, and routing complexity.

Parameter Series-Fed Corporate-Fed
Feed-line length Short—single run through all elements Long—binary splitter tree doubles with each stage
Bandwidth (–1 dB gain) Typically 2–5 % before beam squint degrades pattern 10–15 % or more; path lengths are equalized
Beam squint Present; increases with element count Negligible for balanced trees
Routing area Minimal; one trace per column Large; splitter tree can dominate board area
Sidelobe control Via patch width or coupling gap tapering Via unequal power dividers (Wilkinson, T-junction)
Typical use at 77 GHz Elevation columns (narrow BW acceptable) Azimuth feed when wide BW or scanning needed

Most 77 GHz automotive radar modules use a hybrid approach: series-fed columns for the elevation plane and a corporate feed across columns in the azimuth plane. This balances compactness with the wider instantaneous bandwidth that FMCW chirps demand. For deeper background on how the MMIC connects to these feed lines, see the discussion on radar chip-to-board transitions.

Element Spacing and Grating-Lobe Avoidance

Element spacing d controls two things simultaneously: the main-beam gain and the onset of grating lobes. The classical constraint is d < λ₀ / (1 + |sin θ_max|), where θ_max is the maximum intended scan angle. At 77 GHz (λ₀ ≈ 3.9 mm) with a ±15° scan the maximum spacing is about 3.6 mm in free space. On a substrate with effective permittivity around 2.9 (typical for RO3003 at this frequency) the guided wavelength shrinks, so the physical inter-element distance on the PCB is closer to 2.1–2.3 mm center-to-center for series-fed patches.

Choosing the right laminate is critical because Dk directly sets that guided wavelength. The radar PCB material selection guide compares RO3003, Megtron 7, and other candidates on Dk tolerance, loss tangent, and cost.

Practical Spacing Checklist

  • Verify spacing against the guided wavelength at the highest frequency in the chirp band (e.g., 81 GHz for a 76–81 GHz sweep), not the center.
  • Account for the patch’s own physical length (~λ_g/2) when laying out center-to-center pitch.
  • Leave enough copper between adjacent patch edges for the etch process—at 77 GHz this gap can be as small as 100–150 µm (4–6 mil), which demands a tight etch tolerance class.
  • Simulate mutual coupling between adjacent elements; coupling below –20 dB is a reasonable starting target for sidelobe performance.

Feed-Line Impedance and Amplitude Tapering

In a series-fed array each patch taps power from a traveling wave on the feed line. The fraction of power coupled into each element is set by the width of the connecting microstrip segment or the gap between the line and the patch. To achieve a Taylor or Chebyshev amplitude taper for sidelobe suppression, the coupling must increase toward the end of the array (because less power remains on the line after each tap).

A common implementation at 77 GHz uses quarter-wave transformer sections between patches. The transformer impedance for the n-th element is chosen so that the power split matches the desired taper. For example, an 8-element column with a –25 dB Taylor taper might use transformer impedances ranging from roughly 85 Ω at the first element down to 50 Ω at the last, with the feed-line width changing from about 90 µm to 180 µm on 127 µm (5 mil) RO3003 (Dk ≈ 3.00).

Because these trace widths are narrow and the tolerance budget is tight, Dk stability with temperature matters. A Dk shift of ±0.05 across the operating range can detune the transformer enough to shift the sidelobe level by 2–3 dB. The radar Dk stability requirement article quantifies how TCDk affects array performance.

Beam Squint and Bandwidth Limits

Beam squint is the unavoidable penalty of a series feed: as frequency changes, the electrical spacing between elements changes, and the main beam steers away from broadside. The squint angle Δθ for an N-element array with inter-element spacing d is approximately:

Δθ ≈ arcsin[(Δf / f₀) · (d / λ_g) · N / (N – 1)]

For an 8-element column at 77 GHz with 2.2 mm spacing on RO3003, a 5 GHz chirp bandwidth (76–81 GHz) produces roughly ±3° of squint. In the elevation plane of an automotive radar this is usually acceptable because the elevation beamwidth is already 15–20°. In the azimuth plane it is not, which is why azimuth feeds are almost always corporate.

Reducing squint options include shortening the array (fewer elements), using a resonant standing-wave feed instead of a traveling-wave feed (at the cost of narrower impedance bandwidth), or accepting the squint and compensating in radar signal processing.

PCB Stackup and Fabrication Constraints

A 77 GHz series-fed patch array is typically built on a two-layer or four-layer stackup. The antenna layer sits on the top copper with a continuous ground plane immediately below, separated by 127 µm (5 mil) or 254 µm (10 mil) of low-loss laminate. Thinner substrates give wider impedance bandwidth per patch but make the feed-line impedance more sensitive to etch variation. The radar stackup design guide covers two-layer, four-layer, and hybrid builds in detail.

Critical Fabrication Tolerances

  • Etch tolerance: ±12.5 µm (0.5 mil) or better is needed for 77 GHz patch widths around 1.0–1.2 mm.
  • Dk tolerance: ±0.02 across the panel; verify with the laminate vendor’s lot data.
  • Copper roughness: Rz below 1.5 µm (rolled or VLP foil) to keep conductor loss under control at millimeter-wave frequencies.
  • Registration: Layer-to-layer alignment within ±25 µm so that via fences around the feed network land correctly on their pads.

Via fences running along both sides of the feed line suppress parallel-plate modes that would otherwise radiate and distort the pattern. Typical via pitch is λ_g/10 to λ_g/8, which at 77 GHz means 200–250 µm center-to-center—aggressive but achievable with laser-drilled microvias. More on this in the via fence and launch design article.

System-Level Reliability of the Array Module

Automotive 77 GHz radar module with antenna array and MMIC

A radar antenna array module is a series system from a reliability standpoint: the MMIC, each solder joint in the RF chain, the feed network, and the radome must all function for the module to meet spec. If any single element fails—an open via, a cracked solder ball, a delaminated patch—the array’s amplitude taper is destroyed and sidelobe levels spike. Estimating the combined failure rate early helps set inspection and screening requirements for production.

Loading Series System Reliability…

Enter the failure rates (FIT values) for the MMIC, each connector or transition, and the PCB assembly itself. A typical 77 GHz front-end module with one MMIC (50 FIT), two RF transitions (10 FIT each), and the PCB array (5 FIT) yields a system-level failure rate of 75 FIT, corresponding to roughly 1.5 million hours MTBF. If your target is automotive-grade (below 100 FIT total), this leaves headroom, but adding a second MMIC for MIMO pushes you close to the limit and may require higher-reliability solder processes or underfill.

Ethernet and Data Backhaul Layout

Modern radar modules stream raw ADC data or processed point clouds over automotive Ethernet (100BASE-T1 or 1000BASE-T1). The Ethernet magnetics—typically integrated into a small transformer module—sit between the radar processor and the connector. Placing them correctly matters because their return-loss and common-mode rejection degrade if the layout violates the recommended footprint and routing symmetry specified by the magnetics vendor.

Loading Ethernet Magnetics Layout Tool…

Use this tool to verify pad geometry, trace routing symmetry, and keep-out zones for the magnetics package on your radar module. A well-laid-out 100BASE-T1 interface on the same board as a 77 GHz antenna array requires careful ground partitioning: the Ethernet ground should connect to the radar ground at a single point near the connector to prevent digital return currents from flowing under the antenna aperture and raising the noise floor. Consult TI’s Ethernet PHY layout application note for detailed routing guidelines applicable to automotive radar modules.

Calibration and Production Test

Even a perfectly designed radar antenna array will show unit-to-unit gain and phase variation due to fabrication tolerances. Calibration in an anechoic chamber or with a known reflector corrects these offsets in firmware. The phase error budget across a 12-element azimuth array should stay below ±10° RMS after calibration to keep the first sidelobe within 1 dB of the design target. The radar calibration and phase-error budget article breaks down the contributors.

Design Checklist

  1. Select topology: series-fed columns for elevation, corporate feed for azimuth.
  2. Set element spacing below λ₀/(1 + sin θ_max) at the highest operating frequency.
  3. Taper amplitude distribution using quarter-wave transformer widths; simulate the full column in a 2.5-D or 3-D EM solver.
  4. Verify beam squint across the chirp bandwidth; confirm it falls within the elevation beamwidth.
  5. Choose a laminate with Dk tolerance ≤ ±0.02 and copper roughness Rz ≤ 1.5 µm.
  6. Add via fences at λ_g/10 pitch along feed lines.
  7. Estimate system reliability; ensure total FIT stays within the target.
  8. Lay out Ethernet backhaul magnetics with proper ground partitioning.
  9. Budget ±10° RMS phase error for calibration; plan end-of-line antenna pattern verification.

FAQ

How many elements does a typical 77 GHz radar antenna array have?

Automotive long-range radar modules commonly use 8–12 elements per series-fed column and 4–12 columns in azimuth, depending on the required angular resolution. Newer 4D imaging radar designs push to 48 or more virtual channels using MIMO techniques.

Can FR-4 be used for a radar antenna array at 77 GHz?

No. Standard FR-4 has a loss tangent above 0.02 at millimeter-wave frequencies and uncontrolled Dk, making it unsuitable for 77 GHz patch arrays. Low-loss PTFE or hydrocarbon laminates (RO3003, Megtron 7, CLTE-AT) are required.

What causes high sidelobes in a series-fed patch array?

The most common root causes are amplitude taper errors from etch-width variation, phase errors from Dk non-uniformity across the panel, and parasitic radiation from feed-line discontinuities. Proper via fencing and tight fabrication tolerances address all three.

Does beam squint matter for FMCW radar?

In the elevation plane, moderate squint (±3°) is usually tolerable because the elevation beam is already wide. In azimuth, squint across a 5 GHz chirp bandwidth would smear the angle-of-arrival estimate, so corporate feeds or phase compensation in the digital domain are used. Refer to IEEE’s overview of automotive radar antenna techniques for measured squint data.

Ready for a quotation?

Send your requirements for a material, stackup and manufacturing review. Price and schedule are confirmed for your project.

Upload Gerber