PCB Antenna and Feed Resources

Transmitarray Antenna PCB | Lens Array Fabrication

A transmitarray antenna uses a planar PCB aperture of unit cells to collimate or steer an RF beam, offering the flat profile of a phased array without active phase shifters. This guide covers element design, material trade-offs, layer-count decisions, and…

Multilayer transmitarray antenna PCB with circular copper patch elements on PTFE substrate

What Is a Transmitarray Antenna?

A transmitarray antenna is a flat, multilayer PCB aperture that refracts an incident electromagnetic wave—typically from a feed horn—by applying a position-dependent phase shift through printed unit cells. It functions like a dielectric lens but is lighter, thinner, and easier to manufacture with standard PCB processes. Transmitarrays are now common in Ku-, Ka-, and W-band systems (12–110 GHz) for satcom terminals, 5G fixed wireless, and imaging radar, where a low-profile, high-gain aperture is needed without the cost of a fully active phased array.

Each unit cell is a resonant or multi-layer patch structure whose geometry is tuned to transmit the incident field with a specific phase delay—typically covering a full 360° range across the aperture. By arranging hundreds or thousands of cells whose phases follow a lens-like profile, the transmitarray converts a spherical wavefront into a planar one (or steers it to a desired angle).

How a Transmitarray Differs from a Reflectarray and a Phased Array

Cross-section view of a four-layer transmitarray PCB stackup with coupling slots
Parameter Transmitarray Reflectarray Active Phased Array
Feed blockage None (feed behind aperture) Yes (feed in front) None (corporate feed)
Phase control Passive geometry Passive geometry Active shifters / T/R modules
Layer count 3–6 metal layers typical 1–2 metal layers 6–16+ layers
DC power Zero (passive) Zero (passive) High
Beam steering Fixed or mechanical; reconfigurable with PIN / varactor Fixed or reconfigurable Electronic, wideband
Bandwidth (typical) 5–15 % (single layer); up to 20 %+ (multi-layer) 5–15 % 20–40 %+
Cost per aperture area Low Very low Very high

The main advantage of the transmitarray over a reflectarray is the absence of feed blockage, which improves aperture efficiency by 1–3 dB in many designs. Compared with an active phased array, a passive transmitarray trades electronic beam agility for dramatically lower cost and zero DC consumption—making it attractive for fixed-beam or mechanically scanned applications such as satcom-on-the-move and point-to-point backhaul.

Unit-Cell Design Principles

Phase Range and Transmission Magnitude

A useful unit cell must provide close to 360° of phase shift while keeping insertion loss below about 1–1.5 dB across the operating band. Single-layer cells (one receive patch, one transmit patch, connected by a via or slot) rarely achieve the full range without excessive loss. Multi-layer cells—three or four coupled resonators separated by bonding layers—flatten the transmission magnitude across the phase range and are the standard approach above 20 GHz.

Common Cell Topologies

  • Stacked patches with via interconnect: Two or three circular or square patches on successive metal layers, connected by a plated through-via. Phase is controlled by patch diameter or rotation angle. Straightforward to fabricate but sensitive to via registration.
  • Slot-coupled patches: Receive and transmit patches couple through a resonant slot in a shared ground plane, eliminating the need for a connecting via. Wider bandwidth but requires tight slot-dimension control.
  • Rotation-based (Pancharatnam–Berry) cells: Circularly polarized cells whose transmitted phase equals twice the physical rotation angle. Achieves an inherently linear, geometry-independent 360° phase range. Requires CP feed illumination.
  • Multi-resonator bandpass cells: Three or four metal layers act as a spatial bandpass filter whose phase response is shaped by element dimensions. Offers the widest bandwidth (15–20 %) but demands the most layers.

The choice depends on polarization requirements, bandwidth, and the fabrication capabilities available. For a deeper look at how full-wave solvers set up these element sweeps, see the antenna simulation workflow guide.

Material Selection for Transmitarray PCBs

Material choice directly controls insertion loss, phase accuracy, and mechanical flatness. At Ka-band (26.5–40 GHz) and above, every 0.001 of dielectric loss tangent (Df) matters because the wave passes through multiple dielectric layers.

Material Dk (design) Df (10 GHz) Typical Use
Rogers RO3003 3.00 0.0010 W-band / 77 GHz automotive radar lens arrays
Rogers RT/duroid 5880 2.20 0.0009 Low-loss Ku/Ka-band satcom transmitarrays
Rogers RO4350B 3.48 0.0037 Cost-sensitive sub-20 GHz prototypes
Isola Astra MT77 3.00 0.0017 Multi-layer Ka-band with good bonding compatibility
Panasonic Megtron 7 3.40 0.0015 High-layer-count mmWave arrays needing HDI processes

PTFE-based laminates (RO3003, RT/duroid 5880) deliver the lowest loss but are difficult to drill cleanly and require sodium-etch surface preparation before bonding. Hydrocarbon ceramic laminates (RO4350B) process more like FR-4 but add measurable loss above 30 GHz. For 5G mmWave PCB applications between 28 and 39 GHz, a hybrid stackup—PTFE core layers bonded with low-loss prepreg—often hits the best cost-performance balance. Rogers RO3730, a thick PTFE laminate with Dk 3.0, is another option when large-area antenna panels need mechanical rigidity.

Rogers Corporation’s RO3000 series data sheet provides Dk and Df values up to 77 GHz, which should be used for element tuning rather than the generic 10 GHz catalog numbers.

Stackup Architecture

Typical Four-Metal-Layer Transmitarray

  1. Layer 1 (receive side): Etched receive patches facing the feed horn.
  2. Layer 2 (ground / coupling slot): Continuous copper with etched coupling slots or clearance for vias.
  3. Layer 3 (intermediate resonator): Optional middle patch layer that widens bandwidth.
  4. Layer 4 (transmit side): Etched transmit patches radiating toward the far field.

Bonding layers between cores are typically 2–4 mil (0.05–0.10 mm) low-loss prepreg (Rogers 2929 or Isola 185HR). Total stackup thickness for a Ka-band transmitarray is usually 20–40 mil (0.5–1.0 mm). Thinner stackups reduce surface-wave coupling but are harder to handle in large panels.

Layer Registration and Alignment

Because the receive and transmit patches must be concentrically aligned to maintain the designed phase, layer-to-layer registration tolerance is critical. A misregistration of 1 mil (25 µm) at 30 GHz can shift element phase by 5–10°, degrading sidelobe levels across the aperture. Specify ±2 mil or better registration in the fabrication drawing and use fiducials on every layer.

Fabrication Tolerances That Matter Most

Transmitarray antenna panel on test fixture inside an anechoic measurement chamber

Etch Tolerance

Patch diameter or slot width controls the element phase. At 30 GHz a 0.5 mil (12.5 µm) etch bias across the panel can shift the resonant frequency by 200–400 MHz—enough to move the phase curve by 15–25° at band center. Request etch tolerance of ±0.5 mil or tighter, and ask for etch-compensation data from the fabricator.

Dielectric Thickness

Core and prepreg thickness variations change the coupling between layers and shift the transmission phase. A ±10 % thickness swing on a 4 mil prepreg layer (±0.4 mil) can add ±8° of phase error per cell. Specify pressed-thickness tolerance of ±0.5 mil and verify with cross-section coupons.

Via Drill Accuracy

For via-connected topologies, the via position relative to the patch center must be held within ±1 mil. Laser-drilled microvias (typically 4–6 mil diameter) offer better positional accuracy than mechanical drilling and are preferred above 40 GHz.

Surface Finish

ENIG (electroless nickel immersion gold) adds a 3–5 µm nickel layer that increases conductor loss at mmWave. Immersion silver or bare-copper with OSP is preferred when the transmitarray does not require wire bonding. For more on how protective coverings affect RF performance, the discussion on radome dielectric effects on element tuning applies equally to any layer sitting in the radiating path.

Aperture Layout and Feed Geometry

The feed horn is placed at a distance F from the transmitarray, and the ratio F/D (focal length to aperture diameter) governs the illumination taper and spillover. Typical values are 0.5–1.0. A lower F/D gives a more compact assembly but increases the angle of incidence at edge cells, which degrades their transmission performance because unit cells are usually characterized at normal incidence. Full-wave simulation of edge cells at oblique incidence (up to 30–40°) is essential for accurate gain prediction.

The required phase at each cell position (x, y) relative to the aperture center is:

φ(x, y) = k₀ · (√(x² + y² + F²) − F)  (mod 2π)

where k₀ = 2π/λ₀ is the free-space wavenumber at the design frequency. This profile is discretized to the unit-cell grid, and each cell’s geometry is selected from the pre-simulated phase library.

Measurement and Validation

After fabrication, the transmitarray is mounted in front of its feed horn on a precision fixture and measured in a far-field or compact-range chamber. Key figures of merit are:

  • Gain and aperture efficiency: A well-designed Ka-band transmitarray achieves 40–55 % aperture efficiency (1–2 dB below a comparable parabolic reflector).
  • 1-dB gain bandwidth: Typically 8–15 % for a three-layer design.
  • Sidelobe level: −15 to −20 dB relative to the main beam for a uniform-phase aperture without amplitude taper.
  • Cross-polarization: Better than −25 dB for linearly polarized designs; rotation-based CP cells can reach −20 dB axial ratio bandwidth of 10 %+.

For guidance on chamber setup, probe calibration, and near-field-to-far-field transforms, see the antenna measurement setup guide. Verifying S11 at the feed port is also important—the S11 and VSWR measurement guide covers calibration pitfalls that apply directly.

Scaling from Prototype to Production

A prototype transmitarray is often a single 12 × 12 inch panel with one aperture. Moving to volume production introduces panelization, automated optical inspection (AOI) of every element, and statistical process control on etch and registration. Because every cell is different, standard coupon-based acceptance testing is insufficient—consider adding test cells at the panel border that sample the extremes of the phase library. The antenna prototype-to-production scaling guide discusses yield and tolerance strategies in detail.

The IEEE Transactions on Antennas and Propagation and the IEEE Transactions on Microwave Theory and Techniques contain the primary peer-reviewed literature on transmitarray theory and measured results; searching “transmitarray” in either journal returns hundreds of relevant papers for specific topologies and frequency bands.

Frequently Asked Questions

How many PCB layers does a transmitarray need?

Most practical transmitarrays use three to six metal layers. A minimum viable design has two patch layers and one ground/slot layer (three metals). Adding a fourth metal layer with an intermediate resonator extends the usable bandwidth from roughly 5 % to 12–20 %.

Can FR-4 be used for a transmitarray?

FR-4 is feasible below about 6 GHz where its loss tangent (Df ≈ 0.020) does not destroy the link budget. Above 10 GHz, multi-layer FR-4 transmitarrays suffer several dB of excess insertion loss and are generally impractical. Use PTFE or low-loss hydrocarbon laminates for any design above C-band.

What aperture efficiency can I expect?

Measured Ka-band transmitarrays in the literature report 40–55 % aperture efficiency. Losses come from element insertion loss (0.5–1.5 dB total through all layers), phase quantization, spillover, and oblique-incidence degradation at edge cells.

Is beam steering possible with a transmitarray?

Yes. Mechanical steering (rotating the feed or the panel) is simplest. Electronic reconfigurability is achieved by integrating PIN diodes or varactor diodes into each unit cell, but this adds DC bias routing, increases insertion loss by 1–3 dB, and significantly raises fabrication complexity and cost.

What is the typical element spacing?

Unit-cell pitch is usually 0.4λ₀ to 0.6λ₀ at the design frequency. At 30 GHz (λ₀ = 10 mm), that means 4–6 mm center-to-center. Tighter spacing suppresses grating lobes for wide-angle scanning but demands finer etch and registration tolerances.

Ready for a quotation?

Send your requirements for a material, stackup and manufacturing review. Price and schedule are confirmed for your project.

Upload Gerber