RF PCB Project Services

RF PCB Assembly Service: MMIC Die & Connector

A dedicated RF PCB assembly service handles the unique demands of high-frequency boards—MMIC die bonding, RF connector attachment, shielding, and post-reflow tuning—that general-purpose PCBA lines routinely get wrong.

Solder paste stencil aligned over RF PCB pads on Rogers laminate

What Is an RF PCB Assembly Service?

An RF PCB assembly service is a specialized PCBA workflow built around the materials, components and tolerances unique to high-frequency circuits—typically above 500 MHz and extending into millimeter-wave bands. It covers solder-paste printing on PTFE and ceramic-filled laminates, reflow profiling that respects low-Tg substrates, MMIC die attach with conductive epoxy, wire or ribbon bonding, RF connector soldering, EMI shield installation, and in-circuit RF verification. General SMT houses struggle with these steps because RF substrates warp differently, pad geometries follow transmission-line rules rather than IPC land-pattern tables, and a 0.1 mm misalignment on a coplanar-waveguide launch can shift return loss by 6–10 dB.

Why RF Boards Need a Dedicated Assembly Line

MMIC die with gold wire bonds inside a PCB cavity

Substrate Sensitivity

Rogers RO4350B (Dk 3.48 ± 0.05) and RO3003 (Dk 3.00 ± 0.04) are common in designs from 1 GHz to 77 GHz. These laminates absorb less moisture than FR-4, but their CTE mismatch with standard SAC305 solder creates different stress profiles during reflow. Peak temperature must stay below the laminate’s recommended maximum—typically 260 °C for 10 s on most Rogers materials—while still achieving full wetting. A dedicated RF assembly service maintains pre-assembly baking protocols (usually 2–4 hours at 105 °C for PTFE boards stored more than 48 hours outside dry pack) and runs profiling coupons on the actual production laminate, not on an FR-4 surrogate.

Trace and Pad Geometry Constraints

A 50 Ω microstrip on RO4350B at 10 GHz is roughly 0.44 mm (17.3 mil) wide on a 0.254 mm (10 mil) dielectric. Solder paste registration must hold ±50 µm to avoid bridging or starving the pad, which is tighter than the ±75 µm tolerance most general SMT lines guarantee. Stencil design for RF pads often requires custom aperture reductions, anti-pad relief for ground vias, and separate paste layers for connector flanges versus signal pins.

Component Mix

A single RF module can carry bare MMIC die, wire-bondable QFN packages, through-hole SMA or SMP connectors, press-fit waveguide transitions, and conventional 0201 passives—all on the same board. Sequencing these correctly (reflow first, die attach second, connector soldering third, shield last) prevents thermal damage and keeps rework to a minimum. The full RF assembly process flow from paste printing through shield attachment is worth studying before finalizing a design for manufacturing.

Core Process Steps

Use the quiz below to check which assembly process steps your design actually requires. Enter your component types and frequency range, and the tool returns a recommended process sequence.

Loading Assembly Process Quiz…

If the quiz flags MMIC die attach and wire bonding, plan for a two-pass thermal cycle: a first reflow for surface-mount passives and ICs, then a lower-temperature conductive-epoxy cure (typically 150 °C for 60 min) for the bare die. Trying to combine these into a single reflow almost always damages the die or produces voids under the ground paddle.

Step 1 — Solder Paste Printing

A laser-cut stainless-steel stencil, 100–125 µm thick, is the norm for RF boards. Aperture design follows IPC-7525 stencil design guidelines but adds RF-specific modifications: enlarged thermal-relief apertures for ground paddles that must carry RF return current, and reduced apertures on fine-pitch MMIC pads to prevent solder balling under the die cavity. Type 4 or Type 5 solder paste (particle size 20–38 µm) is preferred for pads narrower than 0.25 mm.

Step 2 — Pick and Place

Placement accuracy of ±25 µm is needed for 0201 passives on RF matching networks, where a 50 µm shift changes the effective inductance of a grounding via path. Vision-aligned nozzles reference fiducials etched into the copper, not the board edge, because PTFE panels can have edge tolerances of ±0.2 mm after routing.

Step 3 — Reflow

A nitrogen-atmosphere convection oven with at least eight independently controlled zones is standard for RF reflow. The profile targets a peak of 245–250 °C for SAC305 on Rogers laminates, with time above liquidus (TAL) of 45–75 s. Nitrogen keeps O₂ below 500 ppm, reducing oxidation on exposed gold-plated RF pads and improving solder wetting on edge-launch connector flanges.

Step 4 — MMIC Die Attach and Wire Bond

Bare GaAs or GaN MMIC die are bonded into milled cavities using silver-loaded conductive epoxy (e.g., Ablebond 84-1LMISR4, thermal conductivity ~25 W/m·K). Bond-line thickness is held to 15–25 µm to keep thermal resistance low and to maintain the designed ground-plane reference. After epoxy cure, 0.7–1.0 mil gold wire bonds or 2 mil gold ribbon bonds connect the die pads to the board’s transmission-line launches. Ball-bond pull strength must exceed 3 gf per JEDEC JESD22-B116 wire-bond pull-test requirements.

Step 5 — RF Connector Soldering

Edge-launch SMA, 2.92 mm (K), and 2.4 mm connectors are typically hand-soldered with a temperature-controlled iron at 350 °C using flux-cored Sn63/Pb37 or SAC305 wire solder. The flange must sit flat against the board edge with less than 50 µm gap to avoid impedance discontinuity. Proper connector footprint design—pad width, ground-via placement, and anti-pad voiding—determines at least half of the connector’s return-loss performance before the soldering iron ever touches the board.

Step 6 — Shield and Lid Attach

Board-level EMI shields (stamped or machined) are soldered onto pre-tinned perimeter pads using selective soldering or a third reflow pass at a lower-melting-point alloy (Sn42/Bi58, mp 138 °C). Removable lids with spring-finger contacts are an alternative when post-assembly tuning is expected.

Step 7 — Cleaning and Inspection

No-clean flux residues that are acceptable on digital boards can increase insertion loss above 20 GHz. RF assemblies are typically cleaned in a deionized-water or semi-aqueous wash, then dried at 60 °C. Inspection combines automated optical inspection (AOI) with X-ray for hidden BGA and die-attach voiding. Void area under MMIC die should be below 25 % of the paddle area per most OEM specifications.

RF Test and Verification

A credible RF PCB assembly service includes at least basic RF verification before shipment. Common tests:

Test Equipment Typical Pass Criteria
Return loss (S11) VNA, calibrated to board connector type ≤ −15 dB across operating band
Insertion loss (S21) VNA, thru-line coupon or DUT Within ±0.3 dB of simulation
Isolation VNA, adjacent channel ports ≥ 20 dB at f₀
Noise figure Noise-figure analyzer + ENR source Per MMIC datasheet ± 0.5 dB
Output power / P1dB Signal generator + power meter Per amplifier spec ± 1 dB

Test fixtures add cost but save yield. A well-designed test jig with spring-loaded coaxial contacts (pogo-pin RF probes) can test 200+ boards per shift with repeatable contact resistance below 0.05 Ω.

Choosing Between Turnkey and Consignment

In a turnkey model the assembler procures every component; in consignment you ship the parts yourself. RF builds add a twist: many MMIC die, LTCC filters and specialty connectors have 12–20 week lead times and are single-sourced. If you already hold these parts, consignment avoids double handling and the markup. If you need the assembler to manage the full BOM, turnkey simplifies logistics but requires a vendor who maintains franchised distributor accounts for RF component lines. A detailed comparison of consignment versus turnkey RF assembly can help you decide which model fits your program.

Optimizing Order Quantity

Assembled RF module with SMA connectors and EMI shield

RF assemblies carry higher NRE (stencils, fixtures, profiling coupons) than standard PCBA, so the per-unit cost drops steeply between 1 and 50 pieces and flattens after about 200. Use the calculator below to find your economic order quantity based on your annual demand, setup cost and holding cost per unit.

Loading Economic Order Quantity…

For example, if your annual demand is 500 RF modules, your setup cost per order is $1,200 (stencil, fixture, profiling), and your holding cost is $8 per unit per year, the EOQ works out to roughly 387 units—suggesting two builds per year is more economical than quarterly batches of 125. Adjust the numbers with your own figures; even a rough EOQ prevents over-ordering expensive RF substrates that may absorb moisture in storage. For high-volume programs, an annual volume pricing agreement locks in per-unit rates and guarantees line time.

Protecting Your Design IP

RF and microwave designs often contain proprietary matching networks, filter topologies or antenna geometries that represent significant R&D investment. Before sending Gerbers or assembly data, ensure your NDA and IP protection agreement is executed. A reputable RF assembly service will sign before any files are reviewed and will maintain physical separation of customer projects on the production floor.

Common Pitfalls and How to Avoid Them

  • Wrong solder-paste type on fine-pitch MMIC pads. Specify Type 4 or 5 in your assembly notes; do not leave it to the operator’s default.
  • Skipping bake-out. PTFE laminates exposed to ambient humidity for more than 48 hours can outgas during reflow, causing solder voids and delamination.
  • Connector torque spec ignored. SMA connectors require 8–10 in·lb torque on the nut. Over-torquing cracks the laminate; under-torquing causes intermittent contact.
  • No RF test before conformal coat. Coating over a failed assembly wastes material and makes rework nearly impossible on PTFE substrates.
  • Mixed-alloy reflow. If leaded solder is used for connectors and lead-free for SMT, document the alloy boundary clearly to avoid unintended mixing during rework.

What to Send Your Assembler

A complete RF assembly package includes:

  1. Gerber files (RS-274X) or ODB++ with all copper, mask, silk and drill layers.
  2. Pick-and-place centroid file with X, Y, rotation and side for every component.
  3. BOM with manufacturer part numbers, approved alternates, and any die-attach or wire-bond specifications.
  4. Assembly drawing noting connector orientation, shield placement, keep-out zones and torque specs.
  5. Reflow profile constraints if the laminate vendor specifies them (e.g., Rogers RO4000 series processing guidelines).
  6. Test plan with pass/fail criteria for any RF measurements to be performed at the assembly house.

Frequently Asked Questions

Can a standard SMT house assemble RF boards?

For simple designs below 3 GHz with only packaged ICs and SMA connectors, a well-equipped general SMT line can manage if you provide detailed process notes. Above 6 GHz, or whenever bare MMIC die, wire bonding or waveguide transitions are involved, a dedicated RF PCB assembly service is strongly recommended to avoid yield loss and performance degradation.

What is the typical lead time for RF assembly?

Prototype quantities (1–10 boards) with all parts on hand typically take 5–10 working days from kit receipt to shipment. Production runs of 50–500 boards take 10–15 working days, depending on the number of process steps (die attach, wire bond, shield) and test complexity.

How much does RF PCB assembly cost compared to standard PCBA?

Expect a 2×–5× premium over commodity PCBA at the same board count, driven by slower placement speeds on mixed-technology boards, nitrogen reflow, die-attach and wire-bond steps, and RF test time. NRE for stencils and fixtures adds $500–$2,000 depending on complexity. Exact pricing depends on BOM, volume and test requirements.

Is lead-free solder acceptable for RF assemblies?

SAC305 is used in most commercial RF products and performs well through Ka-band (26.5–40 GHz). For military or space applications governed by IPC J-STD-001 Class 3 with Space Addendum, tin-lead (Sn63/Pb37) is still the baseline. The choice affects reflow profile, connector soldering temperature and rework procedures.

Do I need to specify the stencil design, or does the assembler handle it?

A qualified RF assembler will design the stencil apertures based on your Gerber paste layer, but you should flag any non-standard requirements—such as reduced apertures for die-attach cavities or home-plate pads for edge-launch connectors—in your assembly drawing. Collaboration at this stage prevents first-article failures.

Get an exact price: send your Gerber files for a free DFM review and a firm RAYPCB quote in hours, not days.

Loading Instant Quote Calculator…

Ready for a quotation?

Send your requirements for a material, stackup and manufacturing review. Price and schedule are confirmed for your project.

Upload Gerber