RF PCB Stackup Planning

2-Layer RT/duroid 5880 Stackup | Lowest Loss Build

A complete guide to specifying a two-layer RT/duroid 5880 stackup, covering material parameters, microstrip geometry, fabrication tolerances, and total landed cost for the lowest-loss RF PCB build available in PTFE laminates.

Two-layer RT/duroid 5880 microstrip PCB with gold finish and white PTFE substrate

What Is an RT5880 Stackup?

An RT5880 stackup is a layer arrangement built on Rogers RT/duroid 5880, a glass-microfiber-reinforced PTFE laminate with a dielectric constant (Dk) of 2.20 ± 0.02 and a dissipation factor (Df) of 0.0009 at 10 GHz. In a two-layer configuration—signal on top, continuous ground on the bottom—it delivers the lowest dielectric loss of any commercially available rigid PCB substrate, making it the default choice for microstrip filters, feed networks, and millimeter-wave test fixtures up to 77 GHz and beyond. If your loss budget cannot tolerate even the 0.0027 Df of RO4350B, RT/duroid 5880 is where you land.

Why a Two-Layer Build Makes Sense for RT5880

Cross-section view of a two-layer PTFE PCB stackup

RT/duroid 5880 is a soft, non-woven PTFE material. Unlike ceramic-filled hydrocarbon laminates, it does not bond easily in multilayer presses. Fusion bonding or prepreg-based multilayer builds with 5880 are possible but expensive, hard to source, and introduce bonding films that raise effective Df. A two-layer microstrip stackup avoids all of that: one copper layer for signal, one for ground, separated by a single dielectric core. The result is the simplest, most repeatable, and lowest-loss RF board you can specify.

When you need more layers—say for a power-distribution plane or digital control lines—consider a PTFE multilayer stackup with fusion-bonded cores, or a hybrid build that pairs an RT5880 signal layer with an FR-4 or polyimide structural layer.

Recommended Two-Layer RT5880 Stackup

Layer Material / Function Thickness Notes
Top copper Electrodeposited (ED) or rolled Cu 0.5 oz (17.5 µm) or 1 oz (35 µm) ½ oz preferred for fine lines ≤ 6 mil
Dielectric core RT/duroid 5880 10 mil (0.254 mm), 20 mil (0.508 mm), 31 mil (0.787 mm), or 62 mil (1.575 mm) Dk 2.20, Df 0.0009 @ 10 GHz
Bottom copper ED or rolled Cu 0.5 oz or 1 oz Unbroken ground plane
Surface finish Immersion gold (ENIG) or electroplated Ni/Au — ENIG typical; electrolytic Au for wire-bond pads

The most common core thicknesses are 10 mil and 20 mil for frequencies above 30 GHz, and 31 mil for Ku- and Ka-band filters where a wider trace is acceptable. The 62 mil core appears mainly in lower-frequency (2–12 GHz) antenna feed networks where mechanical stiffness matters more than line width.

For deeper material data—Dk vs. frequency curves, moisture absorption, and CTE values—see the dedicated RT/duroid 5880 PCB material page.

Microstrip Trace Width vs. Core Thickness

Because RT5880’s Dk is only 2.20, a 50 Ω microstrip line is wider than on higher-Dk substrates. That is usually an advantage: wider traces mean lower conductor loss and more forgiving fabrication tolerances. The table below gives approximate 50 Ω microstrip widths for common core thicknesses, assuming 1 oz copper and ENIG finish.

Core (mil) Core (mm) 50 Ω Width (mil) 50 Ω Width (mm) Typical Use
10 0.254 30 0.76 V-band, E-band, 77 GHz radar
20 0.508 60 1.52 Ka-band filters, test fixtures
31 0.787 94 2.39 Ku-band couplers, power dividers
62 1.575 188 4.78 S/C-band feed networks

These are starting-point values. Your final width depends on copper weight, etch compensation, and the actual Dk at your operating frequency. Always run a field solver with the fabricator’s measured Dk for the specific lot.

Minimum Trace and Space Rules

PTFE substrates etch differently from FR-4. The soft dielectric can deform under mechanical stress, and the copper-to-PTFE adhesion (especially with standard ED foil) is lower, so aggressive trace widths below 4 mil are risky. Most fabricators comfortable with RT5880 quote a minimum trace/space of 4/4 mil for ½ oz copper and 5/5 mil for 1 oz copper. Enter your planned geometry below to check it against standard process rules.

Loading Min Trace Space Rule Checker…

If the checker flags a violation, the first fix is usually to move to ½ oz copper or to widen the gap rather than the trace. On a two-layer RT5880 board the ground plane is continuous, so spacing constraints mainly affect coupled-line structures like edge-coupled filters and Lange couplers.

Loss Budget: Where Every Tenth of a dB Goes

The whole point of choosing RT5880 is loss. A rigorous insertion loss budget for an RT5880 microstrip line at 24 GHz on a 10 mil core with 1 oz copper breaks down roughly as follows:

  • Dielectric loss: ~0.02 dB/cm — dominated by Df of 0.0009.
  • Conductor loss: ~0.06 dB/cm — the dominant term at millimeter-wave; depends on copper roughness (Rz) and skin depth.
  • Radiation loss: negligible for microstrip below 40 GHz on thin substrates.
  • Surface-finish loss: ENIG adds roughly 0.005–0.01 dB/cm vs. bare copper at 24 GHz because of the nickel barrier layer. Immersion silver or OSP avoids this but has shelf-life and wire-bond limitations.

Copper roughness is the hidden variable. Standard ED foil on RT5880 has an Rz of about 6–8 µm. Rogers offers a “low-profile” (LP) version, RT5880LZ, with Rz around 2 µm, which can cut conductor loss by 15–20 % above 20 GHz. Specify LP foil whenever the application is above Ku-band.

Fabrication and Handling Considerations

Ka-band microstrip filter on RT/duroid 5880 PTFE laminate

Drilling

RT5880 is soft enough that standard carbide drills work well, but the low Tg (effectively none—PTFE does not have a classic Tg) means heat management during drilling matters. Use peck drilling for through-holes and keep spindle speeds moderate. Minimum finished hole diameter is typically 8 mil (0.2 mm) for mechanical drills; laser vias are possible but rarely needed on a two-layer board.

Plating and Adhesion

PTFE’s low surface energy makes copper adhesion the single biggest process risk. Sodium-naphthalene or plasma etch surface treatments are standard before plating. Without them, pads can lift during soldering. Confirm with your fabricator that they use a validated PTFE surface-activation process—this is the number-one quality differentiator among RT5880 shops.

Dimensional Stability

RT5880’s CTE in the x-y plane is roughly 31 ppm/°C for the glass-reinforced version and higher for the non-reinforced 5880 variant. For boards larger than 150 × 150 mm, discuss panelization and fixturing with the fabricator to control bow and twist to IPC-6012 Class 3 limits (≤ 0.75 %).

Cost Drivers and Landed Cost

RT/duroid 5880 is one of the most expensive rigid laminates in common use. The major cost drivers are:

  1. Raw laminate price: RT5880 sheets cost several times more than RO4350B per square foot, and lead times can stretch to 8–12 weeks during allocation.
  2. Panel utilization: standard Rogers sheet sizes are 12 × 18 in or 18 × 24 in. Small boards waste material; nesting matters.
  3. PTFE processing surcharge: not every shop handles PTFE. Those that do charge a premium for the sodium-naphthalene or plasma treatment, slower drill cycles, and tighter process controls.
  4. Surface finish: electrolytic gold for wire-bond pads adds significant cost over ENIG.
  5. Import duties and freight: if the laminate ships from the US and the board is fabricated elsewhere, duties on both the raw material and the finished board apply.

Use the calculator below to estimate total landed cost including material, fabrication, finish, and import duties for your specific board dimensions and quantity.

Loading Landed Cost Calculator…

A realistic example: a 50 × 50 mm two-layer RT5880 board on 10 mil core, ½ oz copper, ENIG finish, quantity 50, fabricated in a specialty PTFE shop, typically lands in the range of several hundred dollars for the lot—far more per unit than an equivalent FR-4 board, but a fraction of the cost of a ceramic substrate or LTCC. At volume (1 000+), the per-unit premium drops substantially because the laminate cost is amortized over more boards.

If the RT5880 price is hard to justify, a Taconic RF-35 stackup offers Dk 3.50 and Df 0.0018 at roughly half the material cost—acceptable for many applications below 20 GHz where the extra 0.001 in Df is tolerable.

When to Choose RT5880 vs. Alternatives

Criterion RT/duroid 5880 RO4350B Megtron 6
Dk (10 GHz) 2.20 3.48 3.71
Df (10 GHz) 0.0009 0.0037 0.004
Multilayer ease Difficult Standard FR-4 process Standard FR-4 process
Max practical freq. 110 GHz+ ~40 GHz ~30 GHz
Cost (relative) High Medium Medium-low
Best fit Filters, couplers, test fixtures, mmWave feeds General RF, mixed-signal High-speed digital with RF

Choose RT5880 when dielectric loss must be minimized and the design fits a two-layer microstrip topology. Choose RO4350B when you need multiple layers or mixed-signal integration. For high-speed digital backplanes with embedded RF, a Megtron 6 stackup is more practical. And for millimeter-wave antenna-in-package builds that demand HDI microvias, look at an HDI mmWave stackup on a lower-Dk ceramic or LCP substrate instead.

Design Checklist for a Two-Layer RT5880 Board

  • Confirm the exact RT5880 part number with the fabricator (5880, 5880LZ, or 5880 with non-woven glass).
  • Specify core thickness, copper weight, and foil type (standard ED vs. low-profile) on the fab drawing.
  • Call out the surface-activation process (sodium-naphthalene or plasma) in the procurement spec.
  • Run a 2.5-D field solver (not a static formula) for impedance, using the vendor’s Dk at your operating frequency from the Rogers RT/duroid 5880 datasheet.
  • Include test coupons for impedance verification per IPC-2141A or your internal spec.
  • Specify IPC-6012 Class 3 if the board is for aerospace or defense; Class 2 for commercial.
  • Add fiducials and a ground-plane keepout sketch if the board will be machine-soldered.

Frequently Asked Questions

Can RT5880 be used above 77 GHz?

Yes. RT/duroid 5880 has been characterized and used in published designs up to 110 GHz and beyond. At those frequencies, use the 5 mil or 10 mil core and low-profile foil to keep conductor loss manageable.

Is RT5880 RoHS compliant?

RT/duroid 5880 itself contains no restricted substances under IEC 63000 (RoHS). Compliance of the finished board depends on the solder, plating, and components used during assembly.

What is the shelf life of bare RT5880 laminate?

PTFE laminates do not absorb significant moisture (RT5880 moisture absorption is 0.02 %), so there is no practical shelf-life limit for the raw laminate. However, surface-treated panels awaiting plating should be processed within the fabricator’s specified window—typically 24–48 hours—to maintain adhesion.

Can I solder directly to RT5880 boards?

Yes, but only if the copper adhesion treatment was properly applied. Standard reflow profiles (peak 245 °C for SAC305) are safe; PTFE will not degrade. The risk is pad lift from poor adhesion, not thermal damage to the substrate.

Do I need a solder mask on a two-layer RT5880 board?

Many RF designers omit solder mask entirely on RT5880 to avoid its effect on impedance and loss at millimeter-wave frequencies. If mask is needed for selective soldering, specify a low-Dk mask (Dk ≤ 3.5) and keep it off transmission lines and coupled structures.

Ready for a quotation?

Send your requirements for a material, stackup and manufacturing review. Price and schedule are confirmed for your project.

Upload Gerber