
What Is Radar Frequency Regulation?
Radar frequency regulation is the set of national and international rules that define which spectrum bands a radar sensor may use, how much power it may radiate, what bandwidth it may occupy, and under what conditions it may operate without a site license. Every commercial radar product—automotive, industrial, drone, level-sensing—must comply with these rules before it can be sold. The three frameworks that matter most are the ITU Radio Regulations at the global level, FCC Part 15 and Part 95 in the United States, and ETSI harmonised standards in the European Union.
Getting the regulatory picture right early is not optional—it determines your center frequency, maximum bandwidth, antenna gain budget, and therefore the PCB substrate, trace geometry and shielding strategy for the entire product. This guide walks through the major allocated bands, compares FCC and ETSI requirements side by side, and shows where regulation directly affects hardware design.
ITU Framework: How Radar Spectrum Is Allocated Globally

The ITU Radio Regulations divide the world into three regions and allocate spectrum to the Radiolocation Service (among others). National regulators then adopt, restrict or extend those allocations. For unlicensed short-range radar, the bands that see the most commercial activity are:
- 24.00–24.25 GHz (ISM band, narrow-band radar)
- 24.05–24.25 GHz / 24.00–24.25 GHz UWB (ultra-wideband short-range, sunset in EU)
- 57–64 GHz (V-band, overlapping with WiGig allocations)
- 76–77 GHz (long-range automotive radar)
- 77–81 GHz (short-range automotive and industrial radar)
The ITU allocations are primary or secondary, and whether a national body permits unlicensed operation on top of that allocation varies. This is why a radar module legal in the US may not be legal in Korea or Japan without re-certification at a different power level.
FCC Radar Bands: Part 15 and Part 95
In the United States, most commercial radar sensors operate under FCC Part 15, which permits unlicensed intentional radiators provided they meet specific emission limits. The relevant sub-parts are:
24 GHz Band (§15.245 and §15.249)
Field-disturbance sensors (motion detectors, level sensors) at 24.0–24.25 GHz are permitted under §15.245 with a maximum EIRP of roughly 14.5 dBm for narrowband operation. The wider 22–29 GHz UWB allocation under §15.515 allows higher bandwidth but imposes a spectral density limit of −41.3 dBm/MHz EIRP, which caps practical range.
60 GHz Band (§15.255)
The 57–71 GHz band is available for unlicensed use with an average transmit power up to 40 dBm EIRP (for fixed point-to-point) and 27 dBm for other applications. Radar sensors in this band benefit from enormous bandwidth—up to 14 GHz—enabling sub-centimeter range resolution. The trade-off is severe atmospheric attenuation near 60 GHz due to oxygen absorption (~15 dB/km), which limits this band to short-range indoor or industrial use.
76–81 GHz Band (§15.253)
This is the primary automotive radar band in the US. FCC §15.253 permits vehicular radar in 76–77 GHz at up to 50 dBm EIRP average, and short-range vehicular radar in 77–81 GHz at up to 24.6 dBm average EIRP with a −3 dB bandwidth of at least 500 MHz. Non-vehicular 76–77 GHz operation is also permitted under certain conditions. The 4 GHz of continuous bandwidth from 77 to 81 GHz makes this band the workhorse for FMCW radar chirps that need fine range resolution—a 4 GHz sweep yields a theoretical range resolution of about 3.75 cm.
ETSI Radar Bands: EN 301 091, EN 302 264 and EN 302 729
In Europe, ETSI publishes harmonised standards that, when cited in the Official Journal of the EU, create a presumption of conformity with the Radio Equipment Directive (RED). The key standards for radar are:
24 GHz (EN 302 729, sunset provisions)
The EU allowed wideband automotive radar at 24.00–24.25 GHz under a time-limited exemption that expired on 1 January 2022. New 24 GHz UWB automotive radar products can no longer be placed on the EU market. Narrowband 24 GHz industrial radar (e.g., tank level sensing) remains permitted under EN 302 729 with a maximum mean EIRP of −7 dBm/MHz and a maximum peak EIRP of 20 dBm.
60 GHz (EN 302 567 / EN 305 550)
ETSI allocates 57–66 GHz for wideband data and sensing with a maximum mean EIRP density of 13 dBm/MHz. Radar applications in this band are growing for gesture recognition and vital-sign monitoring, but the power density limits keep range short.
76–77 GHz Long-Range (EN 301 091)
EN 301 091 covers fixed and vehicular radar at 76–77 GHz. Maximum mean power density is −3 dBm/MHz EIRP, with a peak EIRP of 55 dBm. This enables long-range automotive radar (>200 m) with highly directive antenna arrays.
77–81 GHz Short-Range (EN 302 264)
EN 302 264 governs short-range radar in 77–81 GHz. Maximum mean EIRP density is −3 dBm/MHz, peak EIRP is 55 dBm, and the minimum −10 dB bandwidth must be at least 500 MHz. This standard is the European equivalent of FCC §15.253 for the short-range portion and is the regulatory home of most new automotive corner and in-cabin radar sensors.
FCC vs ETSI: Side-by-Side Comparison
| Parameter | FCC (US) | ETSI (EU) |
|---|---|---|
| 76–77 GHz max mean EIRP | 50 dBm (§15.253) | 55 dBm peak; −3 dBm/MHz mean (EN 301 091) |
| 77–81 GHz max mean EIRP | 24.6 dBm average (§15.253) | −3 dBm/MHz mean density (EN 302 264) |
| 77–81 GHz min bandwidth | 500 MHz (−3 dB) | 500 MHz (−10 dB) |
| 24 GHz UWB automotive | Permitted under §15.515 UWB rules | Sunset; no new products after Jan 2022 |
| 60 GHz max EIRP | 40 dBm (point-to-point) | 13 dBm/MHz mean density (EN 302 567) |
| Certification path | FCC ID via Telecommunications Certification Body | CE marking via Notified Body or self-declaration under RED |
| Spurious emission reference | FCC §15.209 | ETSI EN 301 489 (EMC); product standard annex |
The bandwidth definition difference (−3 dB vs −10 dB) is a subtle trap. A chirp that meets the FCC −3 dB rule may fail the ETSI −10 dB rule if the spectral roll-off is too gradual, forcing a redesign of the chirp ramp or the addition of a bandpass filter. Always simulate the occupied bandwidth against both definitions early in the design cycle.
Other Regional Regulators
Japan (MIC), South Korea (MSIT), China (MIIT) and India (WPC) each maintain their own allocations that broadly follow the ITU framework but differ in power limits, mandatory test procedures and in-country certification requirements. Key differences include:
- Japan: 76–81 GHz permitted for automotive radar under ARIB STD-T111. Power limits are comparable to ETSI, but the type-approval process (Giteki mark) requires in-country testing.
- China: 76–79 GHz allocated for vehicular radar. The 77–81 GHz upper portion is not yet fully harmonised, creating risk for 4 GHz wideband designs.
- South Korea: 76–77 GHz and 77–81 GHz permitted, with KC certification. Antenna gain limits may differ from FCC/ETSI.
If you are designing a radar module for global deployment, the safest approach is to design the RF front end for the most restrictive power-density limit across all target markets, then use software-configurable chirp parameters to optimise performance per region.
How Regulation Shapes RF PCB Design

Regulatory constraints do not stay in the compliance department—they flow directly onto the PCB stackup and layout. Here is how:
Frequency Band Determines Substrate Choice
A 24 GHz narrowband radar on standard low-loss FR-4 may be marginal but feasible for short-range industrial use. At 77 GHz, dielectric loss dominates, and you need substrates with Df below 0.003 at the operating frequency—materials like Rogers RO3003 (Dk 3.00, Df 0.0010 at 77 GHz) or Panasonic Megtron 7. The radar PCB material selection process starts with the regulatory band because it sets the frequency, which sets the loss budget.
Bandwidth Determines Trace Tolerance
A 1 GHz chirp at 76–77 GHz has a fractional bandwidth of about 1.3 %. A 4 GHz chirp spanning 77–81 GHz has a fractional bandwidth of about 5 %. The wider the chirp, the tighter the impedance flatness requirement across the band, which means tighter etch tolerances (typically ±0.5 mil or better) and careful attention to how Dk varies across the sweep bandwidth.
EIRP Limits Constrain Antenna Gain and Tx Power
If regulation caps EIRP at 55 dBm peak but your radar IC outputs only 12 dBm, you have a 43 dB antenna gain budget—achievable with a large patch array, but the array size drives the PCB panel dimensions and layer count. Conversely, a low EIRP limit (like the −41.3 dBm/MHz UWB rule) may force you to use a low-gain antenna and accept shorter range, simplifying the PCB but limiting the product’s market positioning.
Spurious Emission Limits Affect Shielding and Filtering
Both FCC §15.209 and ETSI product standards impose strict limits on out-of-band emissions, particularly harmonics. A 77 GHz fundamental has a second harmonic at 154 GHz and a sub-harmonic at 38.5 GHz, both of which must be suppressed. On the PCB, this means proper via stitching around transmission lines to prevent cavity-mode radiation, and sometimes on-board filtering or absorber materials in the shielding cavity.
Certification Testing: What Gets Measured
Regulatory testing for a radar module typically includes:
- Radiated power / EIRP: Measured in an anechoic chamber or OATS at the fundamental frequency, across all chirp configurations.
- Occupied bandwidth: Verified against the −3 dB (FCC) or −10 dB (ETSI) definition.
- Spurious emissions: Scanned from 30 MHz (or 9 kHz for conducted) up to at least the fifth harmonic or 200 GHz, whichever is lower.
- Duty cycle / transmit-on time: Some regulations (e.g., 24 GHz UWB) impose maximum duty cycle limits.
- Frequency stability: The carrier must remain within the allocated band over temperature, supply voltage variation and aging.
Failing any of these at the test lab means a board respin, re-tuning or added shielding—expensive at the prototype stage, catastrophic in production. This is why pre-compliance radar testing with target simulators and OTA setups during development is strongly recommended. Pre-compliance catches 80–90 % of issues at a fraction of the cost of a formal test-lab failure.
Choosing the Right Band for Your Application
The decision is not purely technical—it is regulatory, commercial and supply-chain driven:
- Choose 24 GHz narrowband when you need a low-cost industrial sensor (level, presence detection) with modest range resolution, and your market includes the EU (where wideband 24 GHz is no longer available).
- Choose 60 GHz for very short-range, high-resolution sensing (gesture, vital signs, in-cabin occupancy) where atmospheric attenuation is acceptable and you want wide available bandwidth.
- Choose 76–77 GHz for long-range automotive or infrastructure radar where high EIRP and narrow chirps suffice.
- Choose 77–81 GHz for automotive short/mid-range and industrial radar needing fine range resolution (the 4 GHz bandwidth gives ~3.75 cm resolution) and global regulatory harmony.
For any band above 60 GHz, the PCB becomes a performance-critical component. Substrate Dk tolerance, copper roughness, and layer-to-layer registration all affect whether the final product meets its EIRP, bandwidth and spurious limits. Selecting a microwave-grade PCB with verified RF performance data at the operating frequency is essential, not optional.
Regulatory Trends to Watch
Several developments are reshaping radar frequency regulation:
- 115–300 GHz exploration: The FCC Spectrum Horizons proceeding opened experimental access above 95 GHz. Sub-THz radar for imaging and gesture recognition is an active research area, though commercial allocations are years away.
- Coexistence with 5G and LEO satellites: The 76–81 GHz band sits near 5G mmWave allocations (n257, n258, n261). Regulators are studying interference scenarios, and future standards may tighten out-of-band emission masks.
- Harmonisation of 77–81 GHz globally: China and India are gradually aligning their 77–81 GHz rules with ITU/ETSI, which will simplify global radar module design—but timelines remain uncertain.
- In-cabin and smart-home radar: ETSI and FCC are both refining rules for low-power 60 GHz radar used in occupancy detection and health monitoring, with updated standards expected by 2025–2026.
Practical Checklist for Radar Regulatory Compliance
- Identify all target markets before schematic capture—not after layout.
- Map each market to its regulatory standard and extract the power, bandwidth and spurious limits into a single comparison table for your design team.
- Design the chirp generator for the most restrictive bandwidth definition (usually the ETSI −10 dB rule).
- Budget antenna gain against EIRP limits; leave at least 3 dB of margin for production variation.
- Specify substrate Dk and Df at the actual operating frequency, not the 10 GHz datasheet value. Understand how Dk and Df shift with frequency for your chosen laminate.
- Include shielding and via fencing in the initial layout to control spurious emissions—retrofitting is always harder.
- Run pre-compliance radiated emission scans before committing to formal certification.
- After certification, lock down the production test parameters so that every shipped unit stays within the certified operating envelope.
FAQ
Can I use the same 77 GHz radar module in the US and Europe?
Yes, if the module meets both FCC §15.253 and ETSI EN 302 264 / EN 301 091. The main pitfall is the bandwidth measurement method (−3 dB vs −10 dB) and the EIRP density limit. Design to the stricter of the two and verify with pre-compliance testing in both definitions.
Is 24 GHz automotive radar still legal?
In the US, 24 GHz UWB radar remains permitted under FCC Part 15 UWB rules. In the EU, wideband 24 GHz automotive radar was sunset on 1 January 2022; only narrowband industrial radar at 24 GHz is still allowed. New automotive designs should target 76–81 GHz.
What happens if my radar exceeds the EIRP limit?
The product fails certification and cannot be legally sold. Fixes include reducing transmit power in firmware, decreasing antenna gain (smaller array or wider beamwidth), or adding attenuation in the RF chain—all of which affect range and detection performance.
Do I need a separate certification for each country?
Generally yes. FCC certification covers the US, CE marking (under RED) covers the EU/EEA, and separate approvals are needed for Japan (Giteki), South Korea (KC), China (SRRC) and others. Some mutual recognition agreements exist, but they rarely eliminate the need for in-country filing.
How does regulation affect radar PCB cost?
Regulation drives frequency, which drives substrate choice. A 24 GHz radar on a low-cost PTFE-free laminate is far cheaper per panel than a 77 GHz design requiring Rogers RO3003 or equivalent. Tighter emission masks also increase shielding and filtering complexity, adding cost at both the PCB and module assembly level.
Ready for a quotation?
Send your requirements for a material, stackup and manufacturing review. Price and schedule are confirmed for your project.
