
What Is Antenna Pattern Measurement?
Antenna pattern measurement is the process of recording the radiated (or received) field magnitude and phase of an antenna as a function of direction in space. The resulting radiation pattern reveals gain, half-power beamwidth (HPBW), sidelobe level (SLL), null depth, cross-polarization discrimination, and front-to-back ratio—every parameter a system engineer needs to validate link budgets and interference margins. Measurements are performed in anechoic chambers, outdoor ranges, or compact antenna test ranges (CATRs), each trading cost and frequency coverage for accuracy and turnaround time.
If you are new to interpreting the polar and rectangular plots that come out of a measurement, start with the fundamentals of reading an antenna radiation pattern before diving into the hardware setup described below.
Far-Field vs Near-Field Methods

Far-Field (Direct) Measurement
The antenna under test (AUT) is placed at a distance R ≥ 2D²/λ from the source antenna, where D is the largest dimension of the AUT and λ is the free-space wavelength. At 10 GHz with a 150 mm aperture, the far-field boundary is roughly 1.5 m—manageable in a modest chamber. At 1 GHz with a 600 mm aperture, R jumps to 2.4 m, and outdoor ranges or CATRs become attractive.
Far-field setups are conceptually simple: rotate the AUT on a positioner, record amplitude (and optionally phase) at each angle, normalize to the peak. Gain is extracted by comparison with a reference standard-gain horn whose gain is traceable to a national metrology institute.
Near-Field Measurement
When the far-field distance is impractically large—common above 18 GHz or with electrically large arrays—near-field scanning captures amplitude and phase on a planar, cylindrical, or spherical surface close to the AUT. A near-field-to-far-field (NF-FF) transform then computes the radiation pattern. Planar scanning is fastest but covers only the forward hemisphere; spherical scanning captures the full 4π steradians, essential for base-station or satellite antennas. For a deeper comparison of the two approaches, see near-field vs far-field antenna measurement.
Quick Comparison
| Parameter | Far-Field | Near-Field (Spherical) |
|---|---|---|
| Typical frequency range | 100 MHz – 40 GHz | 500 MHz – 110 GHz |
| Chamber size needed | Large (R ≥ 2D²/λ) | Compact (probe ≈ 3–5 λ from AUT) |
| Phase measurement required | No (amplitude-only OK) | Yes |
| Full-sphere coverage | With roll-over-azimuth positioner | Inherent in spherical scan |
| Gain accuracy (typical) | ±0.3 – 0.5 dB | ±0.2 – 0.4 dB |
| Post-processing | Minimal | NF-FF transform |
Key Parameters Extracted from a Pattern
Gain
Gain is the ratio of radiation intensity in a given direction to the intensity of an isotropic radiator fed with the same accepted power. It rolls up directivity and radiation efficiency into one number. The gain-comparison method uses a calibrated standard-gain horn (e.g., a IEEE Std 149-recommended pyramidal horn) and subtracts the difference in received power between the horn and the AUT at the same range distance. Understanding the distinction between gain and directivity matters here—losses in the feed network, dielectric, and conductor reduce gain below directivity, as explained in our article on antenna gain vs directivity vs efficiency.
Half-Power Beamwidth (HPBW)
HPBW is the angular width between the two directions on either side of the main beam where the field intensity drops to half its peak value (−3 dB). For a uniform rectangular aperture, HPBW ≈ 0.886 λ/D (radians). In practice, amplitude taper across the aperture widens the beam and lowers sidelobes. Measuring HPBW to better than ±0.5° requires angular positioning accuracy of ±0.1° and a well-defined quiet zone in the chamber.
Sidelobe Level and Null Depth
SLL is typically specified as the ratio in dB between the peak of the highest sidelobe and the main-beam peak. Military phased-array specifications often call for SLL ≤ −25 dB, which demands amplitude and phase control across every element—and a measurement dynamic range of at least 40 dB. Null depth between lobes can reach −40 dB or deeper in a well-designed antenna; verifying it requires a low-noise receiver, time gating, and careful absorber placement to suppress chamber reflections.
Cross-Polarization
Rotating a linearly polarized probe or using a dual-port probe lets you measure co-pol and cross-pol patterns simultaneously. For circularly polarized antennas, the key metric is axial ratio, typically required to be below 3 dB across the main beam and operating band.
Test Setup and Calibration
Chamber and Range Geometry
An anechoic chamber lined with pyramidal carbon-loaded foam absorbers suppresses reflections to create a controlled free-space environment. Quiet-zone reflectivity better than −40 dB is standard for most commercial antenna work; military or low-sidelobe measurements push this to −50 dB or beyond. The AUT is mounted on a positioner (azimuth/elevation or roll-over-azimuth) at the center of the quiet zone, and the source antenna illuminates it from the far end.
Instrumentation Chain
- Signal source: a synthesized CW or stepped-frequency generator, phase-locked to a 10 MHz reference.
- Receiver: a vector network analyzer (VNA) or dedicated antenna-measurement receiver with ≥ 80 dB dynamic range.
- Positioner controller: synchronized with the receiver so each data point is tagged with a precise angle.
- Cables: phase-stable coaxial cables (e.g., Sucoflex or Gore) to minimize phase drift during rotation. Cable-induced common-mode currents can distort patterns significantly, a topic covered in detail in our article on antenna feed cable effects.
Calibration Steps
- Perform a full two-port VNA calibration at the cable ends using a known cal kit.
- Measure the reference standard-gain horn in the same position as the AUT; record the peak received power.
- Mount the AUT, align boresight to the source, and verify that the peak reading is within the expected range.
- Run a full angular sweep (typically 0.5° or 1° steps in both principal planes, plus any required conical cuts).
- Normalize the data to the peak and compute gain using the gain-comparison formula: G_AUT = G_ref + (P_AUT − P_ref) dB.
Common Error Sources and How to Manage Them

| Error Source | Typical Impact | Mitigation |
|---|---|---|
| Chamber reflections | ±0.5 dB gain ripple, raised sidelobes | Better absorber, time gating, CATR |
| Positioner misalignment | Beam-pointing error, asymmetric pattern | Laser alignment, optical encoder feedback |
| Cable flexure / phase drift | Phase error in NF scan → pattern distortion | Phase-stable cables, rotary joints, drift correction |
| AUT mounting structure | Scattering, altered impedance | Low-Dk foam support, RF-transparent fixtures |
| Finite scan truncation (NF) | Increased sidelobe error in NF-FF transform | Extend scan area, apply windowing |
Every one of these sources contributes to overall RF measurement uncertainty. A rigorous uncertainty budget—summing range reflectivity, gain-standard uncertainty, receiver linearity, and positioning error in RSS fashion—is essential for any measurement you intend to report on a datasheet.
Pre-Measurement PCB Inspection: Catching Defects Before They Corrupt Data
A flawed PCB antenna can produce a pattern that looks wrong but is actually “correct” for the as-built geometry. Etching defects, delamination, via voids, and misregistration between layers shift resonant frequency, distort the pattern, and degrade gain. Catching these defects before you spend hours in a chamber saves time and prevents false correlation failures between simulation and measurement.
X-Ray Inspection for Hidden Defects
X-ray inspection reveals internal via fill quality, layer-to-layer registration, and solder joint integrity in feed networks—defects invisible to the naked eye. For multilayer antenna PCBs with buried vias or hybrid stackups, X-ray is often the only way to verify that the fabricated board matches the design intent. Use the explorer below to see common X-ray defect patterns and understand what each one looks like in a radiographic image.
A typical finding is a void exceeding 25 % of a via barrel cross-section, which increases via inductance and shifts the impedance of a series feed line. If you spot such a defect, reject the board or at minimum re-measure S11 before committing chamber time. On high-frequency laminates like those in our high-frequency PCB materials guide, even small registration errors can shift a patch antenna’s center frequency by tens of megahertz.
AOI for Surface and Trace Defects
Automated optical inspection (AOI) catches trace-width violations, copper slivers, solder bridges on feed connectors, and missing or misaligned surface-mount matching components. For a printed antenna whose radiation characteristics depend directly on copper geometry, a 25 µm (≈ 1 mil) trace-width deviation can measurably change beamwidth and input impedance at millimeter-wave frequencies. Explore common AOI defect signatures below.
An AOI flag showing a 50 µm nick in a microstrip feed line, for example, creates a localized impedance discontinuity. The resulting mismatch may only add 0.2 dB of return-loss degradation at 5 GHz, but at 28 GHz the same nick represents a much larger fraction of a wavelength and can introduce a noticeable pattern asymmetry. Addressing these findings before measurement avoids chasing phantom design problems.
From Measurement to Production
Once you have a validated pattern on a prototype, the challenge shifts to maintaining that performance across volume production. Process tolerances in etching, lamination pressure, and plating thickness all introduce unit-to-unit variation. Statistical sampling of patterns—measuring a subset of boards per lot and tracking gain, HPBW, and SLL against control limits—is the standard approach. For a practical framework on bridging prototype results to volume yield, see antenna prototype to production.
Frequently Asked Questions
How far away must the source antenna be for a far-field measurement?
The minimum far-field distance is R = 2D²/λ, where D is the largest aperture dimension and λ is the wavelength. For a 100 mm patch array at 24 GHz (λ ≈ 12.5 mm), R ≈ 1.6 m. Below this distance, the phase front is not sufficiently planar, and the measured pattern will show broadened beamwidth and filled-in nulls.
Can I measure antenna patterns with a VNA instead of a dedicated receiver?
Yes. Modern VNAs offer dynamic ranges exceeding 100 dB at narrow IF bandwidths, which is more than adequate. The VNA also provides phase data, enabling near-field-to-far-field transforms. The main limitation is sweep speed when thousands of angular points are needed, but stepped-CW or segmented sweeps mitigate this.
What dynamic range do I need to verify −30 dB sidelobes?
You need at least 10 dB of margin beyond the deepest feature you want to resolve. For −30 dB sidelobes, target ≥ 40 dB of range dynamic range (accounting for path loss, cable loss, and receiver noise floor). For −40 dB nulls, aim for ≥ 50 dB.
Why does my measured gain differ from simulation by more than 1 dB?
Common culprits include cable loss not de-embedded, gain-standard calibration uncertainty, dielectric constant variation in the PCB laminate, and feed-network conductor loss underestimated in simulation. A structured comparison methodology can help isolate the root cause, as described in our guide on antenna simulation vs measurement.
Do I need a full spherical pattern or just principal-plane cuts?
For a pencil-beam antenna (dish, horn, broadside array), two principal-plane cuts (E-plane and H-plane) often suffice for gain, HPBW, and SLL. For antennas with significant off-axis radiation—omnidirectional, wide-scan arrays, or antennas requiring total radiated power (TRP) and total isotropic sensitivity (TIS)—a full spherical measurement per CTIA OTA test plans is necessary.
Ready for a quotation?
Send your requirements for a material, stackup and manufacturing review. Price and schedule are confirmed for your project.
