PCB Antenna and Feed Resources

SIW Antenna Design | Substrate Integrated Waveguide

A practical guide to substrate integrated waveguide (SIW) antenna design on PCB, covering equivalent waveguide width, via fence rules, slot radiator placement, material selection, and fabrication tolerances with interactive calculators.

SIW via fence on a high-frequency PCB laminate

What Is an SIW Antenna?

A substrate integrated waveguide (SIW) antenna is a planar structure that recreates a rectangular metallic waveguide inside a PCB by using two rows of plated-through vias as the narrow walls and the top and bottom copper layers as the broad walls. Longitudinal or transverse slots cut into the top copper radiate electromagnetic energy, forming a low-profile, low-loss antenna that can be manufactured with standard PCB processes. SIW antennas are widely used from 10 GHz through millimeter-wave bands (60 GHz, 77 GHz, and beyond) because they combine the low radiation loss of a waveguide with the integration advantages of printed circuits.

Why Choose SIW Over Microstrip or Stripline?

SIW longitudinal slot array on Rogers substrate

At frequencies above roughly 10 GHz, conventional microstrip lines suffer increasing radiation loss and sensitivity to fabrication tolerances. A stripline avoids radiation but requires internal routing and makes it hard to place radiating elements. SIW fills the gap: it confines the field inside the dielectric between two ground planes, giving waveguide-class Q-factors (typically 200–500 at Ka-band), yet the slots are on the outer copper and radiate freely.

Parameter Microstrip Stripline SIW
Radiation loss High above 20 GHz Very low (shielded) Low (shielded except at slots)
Unloaded Q (30 GHz) ~100 ~250 ~300–500
Integration with planar circuits Excellent Good (internal layer) Good (microstrip-to-SIW transitions available)
Fabrication complexity Low Medium Medium (via fences required)
Suitable frequency range DC–~30 GHz practical DC–~40 GHz ~5–110 GHz demonstrated

For end-fire radiation requirements, a Vivaldi tapered-slot antenna is often preferred, but when broadside radiation, high gain, and compact feed networks are needed, SIW slot arrays are the stronger choice.

Equivalent Waveguide Width and Cutoff Frequency

The fundamental design step is mapping the via-bounded channel to an equivalent solid-wall waveguide. The effective width weff determines the TE10 cutoff frequency. The most-cited empirical formula (Cassivi et al., 2002) is:

weff = w − d² / (0.95 · p)

where w is the center-to-center distance between the two via rows, d is the via diameter, and p is the via pitch (center-to-center spacing along a row). The TE10 cutoff is then:

fc10 = c / (2 · weff · √εr)

For example, on Rogers RO4350B (εr = 3.48 at 10 GHz), setting w = 7.0 mm, d = 0.4 mm, and p = 0.7 mm gives weff ≈ 6.76 mm and fc10 ≈ 11.9 GHz—suitable for a Ku-band slot array operating around 14–15 GHz.

SIW Cutoff and Via Pitch Calculator

Enter your substrate permittivity, via-row spacing, via diameter, and pitch to get the equivalent width and TE10 cutoff frequency instantly. The tool also flags whether your pitch-to-diameter ratio meets the leakage criterion.

Loading SIW Cutoff and Via Pitch Calculator…

If the calculator returns a cutoff above your target operating band, increase w or choose a substrate with higher εr. A practical operating bandwidth sits between roughly 1.25 fc10 and 1.9 fc10 (below the TE20 onset). Values outside that window will either be below cutoff or risk higher-order mode excitation.

Via Fence Design Rules

The via rows must be dense enough to prevent energy leaking between them. Two rules are essential:

  • Pitch-to-diameter ratio: p/d ≤ 2.5 (ideally ≤ 2.0). A ratio above 3 causes measurable leakage loss, especially above 30 GHz.
  • Via diameter: d ≥ λg/5 is a safe minimum, where λg is the guided wavelength in the SIW at the operating frequency. For a 24 GHz design on RO4350B, λg ≈ 9.3 mm, so d ≥ 1.86 mm is theoretically sufficient, but practical PCB drill sizes (0.2–0.5 mm) already satisfy this at mm-wave because the wavelength is short.
  • Antipad clearance: keep the annular ring ≥ 0.1 mm (4 mil) and the antipad-to-antipad gap ≥ 0.15 mm (6 mil) to avoid copper bridging during etching.

For designs above 60 GHz, laser-drilled microvias (d = 0.1–0.15 mm) with pitch as tight as 0.25 mm are common. Confirm your fabricator’s capability before finalizing the layout. The transition from antenna prototype to volume production is where via registration tolerances most often cause yield loss.

Slot Radiator Design

Slots cut into the broad wall of an SIW interrupt the surface current and radiate. The two main configurations are:

Longitudinal Slots (Broadside Arrays)

Slots aligned along the propagation direction, offset alternately from the waveguide centerline. Each slot’s offset controls its excitation amplitude, enabling Taylor or Chebyshev sidelobe tapering. Slot length is approximately λ0/2 (half the free-space wavelength), and inter-slot spacing is close to λg/2 to maintain in-phase excitation. A 1 × 8 longitudinal slot array at 24 GHz on RO4003C can achieve 15–17 dBi gain with sidelobes below −20 dB when properly tapered.

Transverse Slots

Slots perpendicular to propagation, centered on the broad wall. These radiate with a different polarization (E-field along the waveguide axis) and are useful for cross-polarized or dual-pol architectures. Transverse slots are typically narrower (0.2–0.5 mm wide) and require tighter milling tolerances.

Slot Milling Tolerances

Slot width directly affects resonant frequency and coupling. A ±0.05 mm (±2 mil) variation in slot width shifts the resonance by roughly 50–150 MHz at Ka-band, depending on the substrate. Use the tool below to verify that your slot dimensions meet standard milling rules before sending files to fabrication.

Loading Slot Milling Rule Checker…

If the checker flags a violation—for example, a slot width below the minimum end-mill diameter your fab supports (commonly 0.8 mm / 31 mil for mechanical routing, or 0.2 mm / 8 mil for laser)—widen the slot slightly and compensate by adjusting offset or length. For slots narrower than 0.3 mm, confirm that your fabricator offers laser slot cutting or controlled-depth milling.

Material Selection for SIW Antennas

Because the field propagates through the substrate, dielectric loss (Df) directly sets the SIW’s insertion loss per unit length. At 24 GHz, a Df of 0.004 (typical FR-4) translates to roughly 0.3 dB/cm of SIW loss, while RO4350B at Df ≈ 0.0037 gives about 0.25 dB/cm, and RO3003 at Df ≈ 0.0013 drops to roughly 0.09 dB/cm. For long feed networks (8- or 16-element arrays), the cumulative difference is significant.

Laminate εr (10 GHz) Df (10 GHz) Typical SIW Use Case
FR-4 (high-Tg) ~4.3 ~0.020 Prototyping below 6 GHz only
Rogers RO4350B 3.48 0.0037 5–30 GHz, cost-effective production
Rogers RO3003 3.00 0.0013 24–77 GHz automotive radar, low loss
Rogers RT/duroid 5880 2.20 0.0009 Satellite, aerospace, 30–80 GHz
Isola Astra MT77 3.00 0.0017 77 GHz ADAS, volume automotive

Substrate thickness also matters: thicker boards (≥ 0.508 mm / 20 mil) improve bandwidth and radiation efficiency but increase weight. For 77 GHz automotive radar, 0.127–0.254 mm (5–10 mil) cores on RO3003 or Astra MT77 are standard. Rogers RO3003 datasheet provides the full Dk/Df-versus-frequency curves needed for simulation.

Feed Transitions

Cross-section of a substrate integrated waveguide antenna

An SIW must connect to the rest of the circuit, which is usually microstrip or grounded coplanar waveguide (GCPW). The three most common transitions are:

  • Tapered microstrip-to-SIW: A linearly tapered microstrip section widens to match the SIW impedance. Simple, broadband (15–20 % relative bandwidth), and the most popular choice.
  • GCPW-to-SIW: Ground vias alongside the CPW taper into the SIW via fence. Preferred at frequencies above 40 GHz where microstrip radiation loss is problematic.
  • Probe-fed (vertical transition): A plated via from a lower-layer microstrip couples into the SIW through a slot in the bottom ground plane. Used in multilayer stacks for corporate-fed 2-D arrays.

Transition return loss should be better than −15 dB (VSWR < 1.43) across the operating band. Verify this in full-wave simulation; the antenna simulation workflow from HFSS or CST should include the transition as part of the driven model, not as a de-embedded port.

SIW Slot Array Design Workflow

  1. Specify requirements: center frequency, bandwidth, gain, sidelobe level, polarization.
  2. Choose substrate: balance Df, thickness, cost, and fabricator compatibility.
  3. Calculate SIW dimensions: set w for the desired cutoff (use the calculator above), choose d and p satisfying p/d ≤ 2.
  4. Design a single slot: parametric sweep on slot length, width, and offset in a full-wave solver to find the resonant length and desired coupling level.
  5. Lay out the array: space slots at λg/2, apply amplitude taper via offset variation, simulate the full array including mutual coupling.
  6. Add feed transition: design the microstrip-to-SIW taper, optimize for return loss.
  7. Verify fabrication rules: check via drill size, slot milling width, copper registration, and antipad clearance against the fab’s design rule manual.
  8. Prototype and measure: compare measured S11 and VSWR with simulation. Perform antenna pattern measurement to validate gain and sidelobe levels.

Advanced SIW Antenna Variants

Half-Mode SIW (HMSIW)

Cutting the SIW along its symmetry plane and leaving one side open reduces the width by nearly half while preserving the dominant mode field distribution. HMSIW slot antennas are attractive for compact arrays, though the open edge introduces some radiation leakage that must be accounted for in efficiency budgets.

SIW Cavity-Backed Slot

Surrounding a slot with a closed SIW cavity suppresses back-radiation and surface waves, improving front-to-back ratio to 20 dB or more. This topology is popular for 60 GHz indoor communication and 5G mm-wave base-station antennas.

SIW Leaky-Wave Antennas

By introducing periodic perturbations (e.g., transverse slots at sub-wavelength spacing) along an SIW, the structure radiates continuously as a leaky-wave antenna with frequency-scanned beam steering. This eliminates the need for a phase-shifter network, making it appealing for radar and sensing from 24 to 77 GHz.

SIW-Fed Metasurface Antennas

An SIW feed network can excite a metasurface superstrate for gain enhancement, achieving gains above 20 dBi from a single-layer PCB. The SIW distributes power with minimal spurious radiation, and the metasurface shapes the aperture field.

Common Pitfalls and How to Avoid Them

  • Operating too close to cutoff: below 1.2 fc10, group velocity drops sharply, loss increases, and bandwidth collapses. Keep a margin.
  • Ignoring via plating tolerance: a ±0.05 mm variation in via diameter shifts weff and can detune the array by 1–2 %. Include this in Monte Carlo analysis.
  • Using FR-4 above 10 GHz: the Df of standard FR-4 (0.018–0.025 at 10 GHz) makes SIW impractical. Even “low-loss” FR-4 variants (Df ~0.008) are marginal above 15 GHz.
  • Neglecting the back-short: the SIW must be terminated at both ends—either with a matched load or a short (via row). An unterminated end causes a standing wave that distorts the slot excitation.
  • Forgetting the connector launch: an end-launch SMA or 2.92 mm connector adds its own mismatch. Include the connector model or a measured S-parameter block in simulation. IEEE Xplore hosts numerous validated connector de-embedding techniques.

Fabrication Checklist for SIW Antenna PCBs

  • Via drill diameter tolerance: ±0.05 mm (±2 mil) or better.
  • Via position accuracy: ±0.05 mm (±2 mil); tighter for >40 GHz.
  • Slot milling width tolerance: ±0.05 mm mechanical, ±0.025 mm laser.
  • Copper thickness uniformity: ±10 % (affects slot depth on thick copper).
  • Dk tolerance of laminate: ±0.02–0.05 depending on grade; request lot-specific Dk data for production.
  • Surface finish: ENIG or immersion silver preferred; HASL adds uncontrolled thickness variation over slots.
  • Panel registration: ≤ 0.075 mm layer-to-layer for multilayer SIW stacks.

Request an IPC-6012 Class 3 qualification if the board is for aerospace or automotive radar applications.

Frequently Asked Questions

What frequency range suits SIW antennas?

SIW antennas have been demonstrated from 5 GHz to over 100 GHz. They become most advantageous above 10 GHz, where microstrip radiation loss grows and waveguide integration cost is high. The sweet spot for PCB-based SIW is 10–80 GHz.

Can I build an SIW antenna on FR-4?

Only at low frequencies (below ~6 GHz) and for non-critical applications. FR-4’s high Df (0.018–0.025 at 10 GHz) and poorly controlled Dk make it unsuitable for precision SIW designs above 10 GHz.

How many vias per wavelength do I need?

A common guideline is at least 5 vias per guided wavelength (p ≤ λg/5), combined with p/d ≤ 2.5. Meeting both conditions keeps leakage loss below 0.01 dB per via pitch at most mm-wave frequencies.

What gain can an SIW slot array achieve?

A single-row 8-element array typically reaches 15–17 dBi. A 2-D corporate-fed 8 × 8 array can exceed 25 dBi. Gain is ultimately limited by feed-network loss and aperture efficiency, which is typically 60–75 % for well-designed SIW arrays.

How do I transition from microstrip to SIW?

The most common method is a linearly tapered microstrip whose width increases from the 50 Ω line width to approximately the SIW width over a length of λg/4 to λg/2. This achieves better than −20 dB return loss over 15–20 % bandwidth when optimized in simulation.

Ready for a quotation?

Send your requirements for a material, stackup and manufacturing review. Price and schedule are confirmed for your project.

Upload Gerber